Related Questions
What is the correct answer?
4
Two solutions A1 & A2 have pH value of 2 & 6 respectively. It implies that the solution
A. A1 is more alkaline than solution A2
C. A2 is very slightly acidic
What is the correct answer?
4
Materials having resistivity ranging from 1 to 100 ohm. cm is termed as
What is the correct answer?
4
Change in volume of metals from absolute zero temperature to their melting points is
A. Almost same for all metals
B. Different for different metals
C. Less for low melting point metals
D. Less for high melting point metals
What is the correct answer?
4
The noble metals
A. Are exemplified by Na, K and Li
B. Do not resist corrosion very strongly
C. Are the lowermost in the electro-chemical series of metals
What is the correct answer?
4
Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA)?
What is the correct answer?
4
The Al2O3 content of cryolite in Hall- Heroult cell is maintained between __________ percent.
What is the correct answer?
4
The pressure drop per unit length for laminar flow of fluid through a long pipe is proportional to (where, A = cross-sectional area of the pipe & D = Diameter of the pipe)
What is the correct answer?
4
Stresses encountered in the metal forming processes are less than the __________ of the material.
D. Limit of proportionality
What is the correct answer?
4
Energy of the sun arises mainly from __________ reactions.
What is the correct answer?
4
Main constituent of bone ash is
What is the correct answer?
4
Which of the following metals is not subjected to electrolytic refining/purification?
What is the correct answer?
4
For a thermodynamic system undergoing a process, which of the following pairs best expresses the relationship similar to that expressed by the pressure volume plot?
B. Temperature - pressure
What is the correct answer?
4
Machinability of hard alloys and tool steels is improved by
What is the correct answer?
4
In TIG welding, thoriated tungsten electrodes are used, because it
A. Has higher current carrying capacity
B. Has better electron emissivity
C. Is stronger than ordinary tungsten
What is the correct answer?
4
Ganister contains maximum percentage of
What is the correct answer?
4
Strain hardening effect in metals subjected to cold working is due to the __________ mechanism.
What is the correct answer?
4
Co-efficient of performance of a Carnot cycle refrigerator operating between - 23°C and + 27°C is
What is the correct answer?
4
In case of water (Prandtl number ≈ 6) flowing over a flat plate heated over the entire length, the thermal boundary layer thickness as compared to hydrodynamic boundary layer thickness is
What is the correct answer?
4
The burnout heat flux in the nucleate boiling regime is not a function of the
C. Temperature difference
What is the correct answer?
4
On being hit with a hammer, __________ will readily fracture.
What is the correct answer?
4
A common disinfectant used in village wells for disinfection of water is
D. Potassium permanganate
What is the correct answer?
4
In condensers used in thermal power plants, steam is normally used in shell side and cooling water on the tube side, because of the reason that
A. Compared to the mass flow rate of cooling water, the rate of condensation of steam is invariably smaller
B. Maintaining vacuum on tube side is more difficult than that on the shell side
C. Water velocity can be increased conveniently to increase the overall heat transfer co-efficient because of its lower specific volume compared to steam
D. Condenser can act as a storage unit for condensed steam
What is the correct answer?
4
In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will
What is the correct answer?
4
Copper deposits are found in India at the following location:
What is the correct answer?
4
__________ is the trade name assigned to a nonferrous cast alloy composed of cobalt, chromium & tungsten.
What is the correct answer?
4
Steel produced from phosphatic iron is __________ in nature.
What is the correct answer?
4
Case hardening is not done by
What is the correct answer?
4
Air/fuel ratio by weight for combustion of methane with theoretical quantity of air will be about
What is the correct answer?
4
High speed steel tools retain their hardness upto a temperature of __________ °C.
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working