Related Questions
What is the correct answer?
4
A form of stress corrosion failure termed as 'season cracking' is generally observed in
A. Thermosetting polymers
What is the correct answer?
4
Which of the following is preferred for riveting?
What is the correct answer?
4
What is the range of tempering temperature (°C) for most of the materials?
What is the correct answer?
4
Change in volume of metals from absolute zero temperature to their melting points is
A. Almost same for all metals
B. Different for different metals
C. Less for low melting point metals
D. Less for high melting point metals
What is the correct answer?
4
During sensible cooling of air, its wet bulb temperature
A. Decreases but dew point remains constant
B. Increases but dew point remains constant
C. Increases & the dew point decreases
D. Decreases & the dew point increases
What is the correct answer?
4
When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
The material used for coating the welding electrode is termed as the
What is the correct answer?
4
Fine grained steels have
B. Higher tendency to distort
What is the correct answer?
4
Fibre reinforced plastic (FRP) are
A. Made of glass fibre and thermoplastic resins
C. Made of thermosetting resin and glass fibre
What is the correct answer?
4
A particle is settling in a liquid under Stokesian conditions. The free falling velocity of the particle is proportional to
What is the correct answer?
4
Carbon supply in pack carburising process is in the form of
What is the correct answer?
4
Which of the following materials does not form adherent oxide film on surface?
What is the correct answer?
4
The friction factor for the turbulent fluid flow in a rough pipe does not depend upon the
A. Pipe roughness & pipe diameter
What is the correct answer?
4
Out of the following, the alloy which has equal percentage of constituents, is
What is the correct answer?
4
Water-tube boiler is the one, in which
A. Water passes through tubes and flue gases around it
B. Tube carrying hot flue gases are immersed in a pool of water
C. Tubes are placed in vertical position
What is the correct answer?
4
Dowtherm is a
A. High temperature heating medium (a petroleum product)
B. Product of coal tar distillation
C. Very heat sensitive material
What is the correct answer?
4
The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength.
What is the correct answer?
4
Capacity & power requirement for an air compressor working at high altitude compared to sealevel will be
D. Either more or less; depends on the climatic conditions
What is the correct answer?
4
The condition of diffraction from a crystal is given by
What is the correct answer?
4
What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.
What is the correct answer?
4
Annealing of cast iron
A. Softens it to facilitate machining
B. Decreases the free carbon
C. Increases the strength
What is the correct answer?
4
On being hit with a hammer, __________ will readily fracture.
What is the correct answer?
4
In the X-ray radiography technique, the tube voltage for thicker plates as compared to thin plates, should be
A. Higher, as it gives higher wavelength
B. Lower, as it gives higher wavelength
C. Higher, as it gives shorter wavelength
D. Lower, as it gives shorter wavelength
What is the correct answer?
4
__________ remains constant during the adiabatic cooling of moist air.
What is the correct answer?
4
Which of the following is the most suitable abrasive for grinding high tensile strength materials?
What is the correct answer?
4
The pressure outside a bubble/droplet of liquid is __________ the internal pressure.
D. Unpredictable; depends on the bubble size
What is the correct answer?
4
Brittleness induced due to the presence of sulphur in steel can be reduced by adding
What is the correct answer?
4
Natural water contains approximately __________ percent of heavy water.
What is the correct answer?
4
The mechanism involved in the removal of metal in drilling operation is by