Related Questions
What is the correct answer?
4
Which of the following is a commonly used manometric liquid for low pressure range?
What is the correct answer?
4
Coarse grained steels have
B. No tendency to distort
What is the correct answer?
4
Cascade control is
A. The continuous adjustment of the set point index of an automatic control loop by a primary (master) controller
B. Used when changes in process conditions cause serious upsets in the controlled variable
C. Useful to control flow from temperature
What is the correct answer?
4
Good design of the casing of a centrifugal pump aims at minimising the
What is the correct answer?
4
The efficiency of a Carnot heat engine operating between absolute temperatures T1 and T2 (when, T1 > T2) is given by (T1 - T2)/T1. The co-efficient of performance (CO.P.) of a Carnot heat pump operating between T1 and T2 is given by
What is the correct answer?
4
In troposphere (the weather domain), the temperature 't' at height 'h' above the sea level in metres is given by (where, temperature at sea level is 15°C and t is in °C.)
What is the correct answer?
4
Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C.
What is the correct answer?
4
A psychrometer does not measure the __________ temperature of moist air.
What is the correct answer?
4
Which of the following if present in iron ore, enhances its value?
What is the correct answer?
4
Velocity of a gas in sound is not proportional to (where, T = Absolute temperature of the gas. P = Absolute pressure of the gas. y = Ratio of specific heats (Cp/Cv) ρ = specific weight of the gas)
What is the correct answer?
4
The thermodynamic law, = constant, is not followed by the
A. Free expansion of an ideal gas
B. Adiabatic expansion of steam in turbine
C. Adiabatic compression of air
D. Ideal compression of air
What is the correct answer?
4
The elastic strain energy of a unit length of an edge dislocation as compared to that of a screw dislocation is
What is the correct answer?
4
Reynolds number of a fluid flowing in a circular pipe is 10,000. What will be the Reynolds number when the fluid velocity is decreased by 30% & the pipe diameter is increased by 30%?
What is the correct answer?
4
Co-efficient of performance of a Carnot cycle refrigerator operating between - 23°C and + 27°C is
What is the correct answer?
4
Identify the correct statement.
A. Sphlerite is zinc oxide
B. The first law of the thermodynamics is stated as δE = δQ - δW
C. Lead can be produced in a blast furnace
D. T. ferrooxidans is a fungus that can be used for leaching chalcopyrite
What is the correct answer?
4
Which of the following test is used for distinguishing among dry oils, semi-drying oils and non drying oils?
B. Reichert-Meissl value test
What is the correct answer?
4
The same volume of all gases is representative of their
C. Gas characteristic constants
What is the correct answer?
4
With increase in steam pressure, its specific volume decreases
A. Rapidly first and then slowly
C. Slowly first and then rapidly
What is the correct answer?
4
__________ furnace is generally used in the non-ferrous foundries.
What is the correct answer?
4
Material of construction of the electrode used in the electric resistance welding is
What is the correct answer?
4
What is the value of entropy at 273°K?
What is the correct answer?
4
Joining of thin foils is preferred to be done by
What is the correct answer?
4
Corrosion is
D. An uncontrollable phenomenon
What is the correct answer?
4
While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the
C. Better finish and surface appearance
D. High plastic deformation
What is the correct answer?
4
Pick out the wrong statement.
A. Cold cracking of a weld is due to the presence of hydrogen gas in the weld
B. True stress is given by, σ = σE (1 + εE), where σE and εE are engineering stress and engineering strain respectively
C. Phosphorous can be easily recovered in the iron blast furnace
D. High residual stress at the surface is beneficial for fatigue properties of a material
What is the correct answer?
4
Which of the following is not categorised as the ore agglomeration process?
What is the correct answer?
4
Metal shots used in shot blasting are made of
What is the correct answer?
4
__________ property of a material is determined by the Herbert Pendulum device.
What is the correct answer?
4
The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times.
What is the correct answer?
4
Which one of the following is incombustible?