Related Questions
What is the correct answer?
4
Atomic __________ is a whole number for an element.
What is the correct answer?
4
Closeness of packing is maximum in case of __________ crystal lattice.
What is the correct answer?
4
__________ is a special constituent of chlorophyll without which photosynthesis is not possible.
What is the correct answer?
4
Internal energy of a gas obeying Van-Der- Waals equation of state, [p + (a/v2)] (V - b) = RT, depends upon its
A. Pressure & temperature
B. Pressure & specific volume
C. Temperature & specific volume
What is the correct answer?
4
Which of the following is a boiler accessory
i.e., not a boiler mounting?
What is the correct answer?
4
Energy to be supplied to the radioactive nucleus for the emission of a neutron is __________ MeV.
What is the correct answer?
4
Percentage of argon (by volume) in dry atmospheric air is about
What is the correct answer?
4
Nusselt number is related to Grashoff number (Gr) in turbulent & laminar flow respectively, in respect of free convection over a vertical flat plate as
What is the correct answer?
4
The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it.
What is the correct answer?
4
The life of a ball bearing is inversely proportional to
What is the correct answer?
4
__________ pipe is the most suitable for carrying sanitary drainage.
B. Reinforced cement concrete
What is the correct answer?
4
__________ metal is used as a bearing liner material.
What is the correct answer?
4
Increasing sulphur content in pig iron tends to make it
What is the correct answer?
4
The effect of friction on the flow of steam through a nozzle is to decrease the __________ of steam.
What is the correct answer?
4
For which pair of the fuel gases, calorific value (C.V.) of one fuel is almost double that of the other on volume basis (i.e., kcal/Nm3) while the C.V. is same on weight basis (i.e., kcal/kg)?
C. Sewage gas and gobar gas
D. B.F gas and coke oven gas
What is the correct answer?
4
Ceramic compounds as compared to metallic compounds
B. Resist greater tensile stress at room temperature
C. Have higher melting temperature
D. Are better conductor of electricity at higher temperature
What is the correct answer?
4
Isotropic materials have the same __________ in all directions.
What is the correct answer?
4
Shampoos are commercially not available in the form of
What is the correct answer?
4
The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
What is the correct answer?
4
Pick out the wrong statement about coating/electroplating of metals.
A. Phosphate coating is used as an excellent base for paints & enamels
B. Phosphate coating is less corrosion resistant than chromate coating
C. The base metal to be electroplated is normally made the cathode of the electrolytic cell and coating metal is made the anode
D. Calorising is the process of coating steel with chromium
What is the correct answer?
4
In a good rimming steel
A. Carbon and silicon should be low
B. Silicon should be low but carbon should be high
C. Both silicon & carbon should be high
D. Silicon should be high but carbon should be low
What is the correct answer?
4
A high pressure boiler generates steam at a pressure greater than __________ kg/cm2.
What is the correct answer?
4
Gratings is associated with the measurement of
What is the correct answer?
4
What is the value of entropy at 273°K?
What is the correct answer?
4
Metal shots used in shot blasting are made of
What is the correct answer?
4
When the wet steam is throttled but still remains wet at the exit of the throttle valve, then its temperature & dryness fraction respectively
What is the correct answer?
4
The escape velocity of a body on earth which is independent of its mass is about __________ km/second.
What is the correct answer?
4
'Dikes' are low height walls made around the storage vessels meant for storing hazardous & inflammable material (e.g., petroleum products). Volume of dikes is equal to (where, V = volume of the storage vessel)
What is the correct answer?
4
A highly elastic material is deformed least on loading and retains its original form on removal of the load. Which of the following is the most elastic material?
What is the correct answer?
4
Shrinkage allowance on pattern is provided to compensate for shrinkage when the
A. Metal changes from liquid state to solid state at freezing temperature
B. Solid phase temperature drops from freezing temperature to the room temperature
C. Liquid metal temperature drops from pouring temperature to room temperature
D. Liquid metal temperature drops from pouring temperature to freezing temperature