How can the drafter prevent Auto-CAD from placing or stacking another center mark on a circle when adding a diameter dimension to it?
Explode the dimension and then erase the center mark
Use the Properties dialog box to turn off the center mark of the dimension
It can't be done
Use the trim tool to take away the stacked center mark
Correct Answer :
B. Use the Properties dialog box to turn off the center mark of the dimension
Related Questions
This type of thread is a thread on the inside of a member:
Basic thread
External thread
Internal thread
Major diameter thread
In this type of drawing, vertical pipes may be revolved into the horizontal plane:
Standard view
Elevation view
Transverse piping
Developed piping
In isometric projection, all distances are approximately this percentage of their true size:
120 percent
80 percent
50 percent
20 percent
In order to set drawing limits for a C size architectural drawing the drafter should set the limits to ________.
0, 0 and 2, 9
0, 0 and 17, 11
0, 0 and 18, 24
0, 0 and 34, 24
A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line across the part.
Offset
Half
Whole
Broken out
In some circumstances an entire drawing can be inserted into a different drawing as a block. When this is used the base point will default to ________.
0, 0
10, 10
20, 20
30, 30
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
Client
CAD trainee
Receptionist
Checker
When drawing a line using the relative coordinate system a line is created from ________.
0, 0
The ending point of the last line
The beginning point of the last line
None of the above
If a plane is parallel to the plane of projection, it appears:
True size
As a line or edge
Foreshortened
As an oblique surface
The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section.
Full
Half
Quarter
None of the above
The type of line that projects from an object for the express purpose of locating a dimension is a ________ line.
Visible
Hidden
Extension
Dimension
When using versions of Auto-CAD prior to Release 2006 it may be necessary to ________ a block in order to edit it.
Copy
Explode
Offset
None of the above
In multi-view drawing it is common practice to include three views, the front, the top and the right side. If no dimensions are required on the right side view the drafter can ________.
Leave the view as is
Eliminate the view
Use the left view instead
None of the above
This type of section is limited by a break line:
Removed section
Revolved section
Broken-out section
Half section
These breaks are used to shorten the view of an object:
Section breaks
Aligned breaks
Conventional breaks
Full breaks
In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:
Removed section
Revolved section
Auxiliary section
Partial section
In these drawings it is necessary to show cut surfaces and distinguish between adjacent parts:
Auxiliary drawings
Assembly sections
3D assemblies
Parts lists
In U.S. structural and architectural drafting, all dimensions of this length are usually expressed in feet and inches:
One inch or over
One foot or over
One yard or over
One rod or over
These drawings are given to contractors to perform work or manufacture individual parts:
Assembly details
3D drawings
Working drawings
Skeleton assemblies
The ________ is a standard element of a section view in a technical drawing.
Cutting Plane line
Section lines
Material hatch pattern
All of the above
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
Pull the line from away from the starting point very carefully
Insure that Ortho is on
Enter 3 for the length of the line
Read the coordinate position on the Dynamic Readout
The maximum and minimum sizes of a feature are identified by a ________ tolerance.
Limits
GD&T
Reference
Allowance
The architectural and construction industries use the United States National CAD standard (NCS) system on many ________ projects.
Residential
Commercial
Aerospace
Publicly funded
The organized and orderly approach to solving problems is known as the:
Engineering process
Design process
Aesthetic process
Functional process
The Free Orbit tool is found on the ________ toolbar.
Rotate
Move
Modify
3-D Move
This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment:
Lug
Boss
Chamfer
Spotface
When creating a Cutting Plane line with Auto-CAD it is customary to use a ________ to create the line.
Center line
Polyline
Dashed line
Hatch line
In this type of concrete, the steel is pre-tensioned before the superimposed load is applied:
Aggregate
Pre-stressed
Reinforced
Preloaded
The title block used on working drawings should include the __________.
Sheet number
Line type
Layer set
All of the above
An accurate record of changes made to release drawings is tracked via this:
A revision block
The basic title form
Working drawings
Portable documents