Related Questions
What is the correct answer?
4
In order to convert fractional inches into decimal inches ________.
A. Look on a metric conversion chart
B. Divide the numerator (top number) by the denominator (bottom number)
C. Check the engineer's scale
What is the correct answer?
4
If a designer is developing a plan for a project in which the entire part is made out of ¾ thick plywood and he only wants to use one view, he should use the ________ view.
What is the correct answer?
4
In these drawings it is necessary to show cut surfaces and distinguish between adjacent parts:
What is the correct answer?
4
In working drawings, these show all necessary information not given directly on the drawing with its dimensions and notes:
D. Title and record strips
What is the correct answer?
4
The bounding box method for setting up an isometric drawing helps the drafter ________.
A. Confine the isometric drawing to its maximum size
B. Figure what lines are to be illustrated vertical and horizontal
C. Position the isometric drawing in paper space
What is the correct answer?
4
Traditional drafters need to be able to create several different line widths because ________.
A. Different line widths convey different information
B. The line width has to do with how dark it appear in the finished drawing
C. They seem to transmit better in a fax machine
D. It makes no difference
What is the correct answer?
4
Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
A. Door openings and walls
What is the correct answer?
4
This is the measured size of a finished part:
What is the correct answer?
4
This is the plane upon which the top view is projected:
What is the correct answer?
4
Once a drawing is determined to be complete, the title block is used to document the change from:
A. A draft to a finished drawing
B. A finished to a working drawing
C. An assembly to a finished drawing
D. A working drawing to a draft
What is the correct answer?
4
The ________ dimension tool will place the length of an angled line.
What is the correct answer?
4
In offset sections, offsets or bends in the cutting plane are all:
C. Either 90 or 180 degrees
What is the correct answer?
4
This is a rounded exterior blend between surfaces:
What is the correct answer?
4
This type of rapid prototyping system uses a laser to fuse powdered metals, plastics, or ceramics:
A. Fused deposition modeling
B. Stereo lithography apparatus
D. Selective laser sintering
What is the correct answer?
4
Baseline dimensions are referenced from a common geometric feature known as a ________.
What is the correct answer?
4
This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment:
What is the correct answer?
4
In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:
What is the correct answer?
4
Technical drawings typically serve one of three purposes:
A. Visualization, Communication, or Documentation
B. Visualization, Dimensioning, or Documentation
C. Communication, Documentation, or Installation
D. Documentation, Installation, or Engineering
What is the correct answer?
4
This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
What is the correct answer?
4
In oblique sketches, the most commonly used angles for receding lines are:
What is the correct answer?
4
Given a situation in which the drafter has crossed extension lines in a drawing what can be done to clean up the point of crossing?
A. Use the Modify tool to clean up the extension lines
B. Use the Tolerance tool to clean up the extension lines
C. Use the Break tool to clean up the extension lines
D. Use the stretch tool to clean up the extension lines
What is the correct answer?
4
Dimensions are used on the elevation plan to describe ________.
A. Finished floor elevations
What is the correct answer?
4
One critical issue drafters need to pay close attention to is the ________.
What is the correct answer?
4
The standard number of threads per inch for various diameters is the:
What is the correct answer?
4
These units are based on inch-foot and yard measurements:
A. International customary units
D. ISO international units
What is the correct answer?
4
Three dimensional models are often used in the design process to __________.
A. Help the client understand the overall design concept
B. Help the client select a color for their carpet
C. Provide the client with a model which they can use to impress their friends
D. Determine the quantity of brick needed to build the house
What is the correct answer?
4
When dimensioning piping drawings, you give the lengths of all runs of this type:
What is the correct answer?
4
The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section.
What is the correct answer?
4
CAD programs which incorporate parametric modeling utilize a system in which the dimensions control the ________.
A. Size and shape of the model features
B. Perspective of the model
C. Shading used to render the model
What is the correct answer?
4
When the receding lines are true length, and the projectors are at 45 degrees to the plane of projection, the oblique drawing is called this:
C. Axonometric projection