If a material expands freely due to heating it will develop
Thermal stresses
Tensile stress
Bending
No stress
Correct Answer :
D. No stress
Related Questions
The weakest section of a diamond riveting is the section which passes through
The first row
The second row
The central row
One rivet hole of the end row
If a material expands freely due to heating it will develop
Thermal stresses
Tensile stress
Bending
No stress
Kelvin-Planck's law deals with
Conservation of work
Conservation of heat
Conversion of heat into work
Conversion of work into heat
The efficiency and work ratio of a simple gas turbine cycle are
Very low
Low
High
Very high
The buckling load for a given column depends upon
Area of cross-section of the column
Length and least radius of gyration of the column
Modulus of elasticity for the material of the column
All of the above
Two shafts 'A' and 'B' transmit the same power. The speed of shaft 'A' is 250 r.p.m. and that of shaft 'B' is 300 r.p.m.
The shaft 'B' has the greater diameter
The shaft 'A' has the greater diameter
Both are of same diameter
None of these
The hard coke is obtained when carbonisation of coal is carried out at
300° to 500°C
500° to 700°C
700° to 900°C
900° to 1100°C
In the below figure, the plastic range occurs
Before point A
Beyond point A
Between points A and D
Between points D and E
The fuel mostly used in blast furnace for extracting pig iron from iron ores is
Hard coke
Soft coke
Pulverised coal
Bituminous coal
The gas constant (R) is equal to the __________ of two specific heats.
Sum
Difference
Product
Ratio
The efficiency of the dual combustion cycle for the same compression ratio is __________ Diesel cycle.
Greater than
Less than
Equal to
None of these
The intensity of stress which causes unit strain is called
Unit mass
Modulus of rigidity
Bulk modulus
Modulus of Elasticity
The atomic mass of nitrogen is __________ oxygen.
Equal to
Less than
More than
None of these
The absolute zero temperature is taken as
-273°C
73°C
237°C
-237°C
The amount of heat required to raise the temperature of __________ water through one degree is called kilojoules.
1 g
10 g
100 g
1000 g
The root mean square velocity of the gas molecules is given by (where k = Boltzmann's constant, T = Absolute temperature, and m = Mass of one molecule of a gas)
√(KT/m)
√(2KT/m)
√(3KT/m)
√(5KT/m)
If the radius of wire stretched by a load is doubled, then its Youngs modulus will be
Doubled
Halved
Becomes four times
None of the above
The neutral axis of the cross-section a beam is that axis at which the bending stress is
Zero
Minimum
Maximum
Infinity
For the constant pressure and heat input, the air standard efficiency of gas power cycle is in the order
Dual cycle, Diesel cycle, Otto cycle
Otto cycle, Diesel cycle, Dual cycle
Dual cycle, Otto cycle, Diesel cycle
Diesel cycle, Otto cycle, Dual cycle
In a uniform bar, supported at one end in position, the maximum stress under self weight of bar shall occur at the
Middle of bar
Supported end
Bottom end
None of these
Workdone in a free expansion process is
Zero
Minimum
Maximum
Positive
Formula based on IS codes is based on
Straight line formula
Eulers formula
Rankines formula
Secant formula
The distance between the centres of the rivets in adjacent rows of zigzag riveted joint is known as
Pitch
Back pitch
Diagonal pitch
Diametric pitch
In a belt drive, the pulley diameter is doubled, the belt tension and pulley width remaining same. The changes required in key will be
Increase key length
Increase key depth
Increase key width
Double all the dimensions
A body is subjected to a tensile stress of 1200 MPa on one plane and another tensile stress of 600 MPa on a plane at right angles to the former. It is also subjected to a shear stress of 400 MPa on the same planes. The maximum normal stress will be
400 MPa
500 MPa
900 MPa
1400 MPa
A close cycle gas turbine gives __________ efficiency as compared to an open cycle gas turbine.
Same
Lower
Higher
None of these
A cube subjected to three mutually perpendicular stress of equal intensity p expenses a volumetric strain
3p/E × (2/m - 1)
3p/E × (2 - m)
3p/E × (1 - 2/m)
E/3p × (2/m - 1)
In the below figure, the stress corresponding to point D is
Yield point stress
Breaking stress
Ultimate stress
Elastic limit
The shear force diagram of a cantilever beam of length l and carrying a uniformly distributed load of w per unit length will be
A right angled triangle
An isosceles triangle
An equilateral triangle
A rectangle
One kg of carbon monoxide requires __________ kg of oxygen to produce 11/7 kg of carbon dioxide gas.
4/7
11/4
9/7
All of these