If T₁ and T₂ are the tensions on the tight and slack sides of the belt respectively, and Tc is the centrifugal tension, then initial tension in the belt is equal to
T₁ - T₂ + Tc
T₁ + T₂ + Tc
(T₁ - T₂ + Tc)/2
(T₁ + T₂ + Tc)/2
Correct Answer :
D. (T₁ + T₂ + Tc)/2
Related Questions
A self locking screw has
Fine threads
Course threads
Coefficient of friction is greater than tangent of load angle
Hole for inserting split pin
For a shaft diameter of 100 mm, the number of bolts in a flange coupling should be
4
6
8
10
Lewis form factor for 14 ½° composite and full depth involute system is (where T = Number of teeth)
0.124 - (0.684/T)
0.154 - (0.912/T)
0.175 - (0.841/T)
None of these
In block brakes, the ratio of shoe width to wheel diameter is taken between
0.1 and 0.25
0.25 and 0.50
0.50 and 0.75
0.75 and 1
In a hydrodynamic lubricated bearing
There is a thick film of lubricant between the journal and the bearing
There is a thin film of lubricant between the journal and the bearing
The lubricant is forced between the journal and the bearing, by external pressure
There is no lubricant between the journal and the bearing
The process extensively used for making bolts and nuts is
Hot piercing
Extrusion
Cold peening
Cold heading
The belt slip occurs due to
Heavy load
Loose belt
Driving pulley too small
Any one of the above
The stress induced in the belt is,
Tensile stress
Compressive stress
Direct shear stress
Torsional shear stress
While designing a screw in a screw jack against buckling failure, the end conditions for the screw are taken as
Both the ends fixed
Both the ends hinged
One end fixed and the other end hinged
One end fixed and the other end free
The modulus of elasticity for mild steel is approximately equal to
80 kN/mm²
100 kN/mm²
110 kN/mm²
210 kN/mm²
The radial distance of a tooth from the pitch circle to the top of the tooth is called
Addendum
Dedendum
Clearance
Working depth
For standard coarse threads of nut, the threads will be as strong in failure by shear as the bolt in tension, if the height of nut (h) is approximately
0.4 times
0.6 times
0.7 times
0.8 times
The gears are termed as medium velocity gears, if their peripheral velocity is
1-3 m/s
3-15 m/s
15-30 m/s
30-50 m/s
Multiple threads are used to secure
Low efficiency
High efficiency
High load lifting capacity
High mechanical advantage
A metal pipe of 1 m diameter contains a fluid having a pressure of 1 N/mm². If the permissible tensile stress in the metal is 20 N/mm², then the thickness of the metal required for making the pipe will be
5 mm
10 mm
15 mm
25 mm
In skew bevel gearing, the axes of shafts are
Intersecting and the teeth are curved
Non-intersecting and nonparallel and the teeth are curved
Non-intersecting and non-parallel and the teeth are straight
None of the above
In a butt welded joint, the size of weld is __________ the throat of weld.
0.5 times
Equal to
2 times
Double
Which process will increase the fatigue duration of parts?
Finishing and polishing
Shotpeening
De-carburisation
Electroplating
According to Rankine's theory, the failure occurs at a point in a member
When the maximum shear stress in a biaxial stress system reaches the shear stress at elastic limit in a simple tension test
When the maximum principal stress in a biaxial stress system reaches the elastic limit of the material in a simple tension test
When the strain energy per unit volume in a biaxial stress system reaches the strain energy at the elastic limit per unit volume as determined from a simple tension test
When the maximum principal strain in a biaxial stress system reaches the strain at the elastic limit as determined from a simple tension test
In a belt drive, if the pulley diameter is doubled keeping the tension and belt width constant, then it will be necessary to
Increase the key length
Increase the key depth
Increase the key width
Decrease the key length
The spring mostly used in gramophones is
Helical spring
Conical spring
Flat spiral spring
Volute spring
A type of brake commonly used in motor cars is a
Shoe brake
Band and block brake
Band brake
Internal expanding brake
A screw is said to be over hauling screw, if the
Friction angle is less than helix angle
Friction angle is more than helix angle
Friction angle is equal to helix angle
Efficiency of screw is 100%
Two shafts of the same length and material are joined in series. If the ratio of their diameters is 2, then the ratio of their angles of twist will be
2
4
8
16
The strength of a riveted joint is equal to
Tearing strength of plate (Pt)
Shearing strength of rivet (Ps)
Crushing strength of rivet (Pc)
Least value of Pt Ps and Pc
Which one of the following loading is considered for the design of axles?
Bending moment only
Twisting moment only
Combined bending moment and twisting moments
Combined action of bending moment, twisting moment and axial thrust
Crushing resistance required to crush the rivet per pitch length is
p.d.σc
p.t.σc
n.d.t.σc
(p - d) t.σc
The suitable material for belt in agricultural machinery is
Leather
Rubber
Cotton duck
Balata gum
An imaginary circle which by pure rolling action gives the same motion as the actual gear, is called
Addendum circle
Dedendum circle
Pitch circle
Clearance circle
The stretching in a belt can be controlled by __________ the stress in the belt.
Reducing
Increasing
Both A and B
None of these