Home
Current Affairs January 2024

What is the correct answer?

4

If the tearing efficiency of a riveted joint is 75%, then the ratio of diameter of rivet to the pitch is equal to

A. 0.2

B. 0.25

C. 0.50

D. 0.6

Correct Answer :

B. 0.25


Related Questions

What is the correct answer?

4

A type of brake commonly used in motor cars is a

A. Shoe brake

B. Band and block brake

C. Band brake

D. Internal expanding brake

What is the correct answer?

4

The temperature required for full annealing in hypereutectoid steel is

A. 50°C above upper critical temperature

B. 50°C below upper critical temperature

C. 50°C above lower critical temperature

D. 50°C below lower critical temperature

What is the correct answer?

4

In nitrated parts, the origins of the fatigue cracks will occur at

A. Surface

B. Just below the surface

C. Within the core

D. None of the above

What is the correct answer?

4

A tapered key which fits in a key way in the hub and the bottom of which is shaped to fit the curved surface of the shaft, is known as,

A. Hollow saddle key

B. Hollow key

C. Soft key

D. None of these

What is the correct answer?

4

In hydrostatic bearings

A. The Oil film pressure is generated only by the rotation of the journal

B. The oil film is maintained by supplying oil under pressure

C. Do not require external supply of lubricant

D. Grease is used for lubrication

What is the correct answer?

4

The creep in the belt is due to

A. Effect of temperature on belt

B. Material of belt

C. Unequal extensions in the belt due to tight and slack side tensions

D. Stresses beyond elastic limit of belt material

What is the correct answer?

4

Which of the following statement is correct?

A. The cold rolled shafting is stronger than hot rolled shafting

B. The hot rolled shafting is stronger than cold rolled shafting

C. The cold rolled and hot rolled shaftings are equally strong

D. The shafts are not made by rolling process

What is the correct answer?

4

An imaginary circle which by pure rolling action gives the same motion as the actual gear, is called

A. Addendum circle

B. Dedendum circle

C. Pitch circle

D. Clearance circle

What is the correct answer?

4

The crest diameter of a screw thread is same as

A. Major diameter

B. Minor diameter

C. Pitch diameter

D. Core diameter

What is the correct answer?

4

The steel pulleys are __________ in weight than cast iron pulleys of the same capacity.

A. Heavier

B. Lighter

C. Moderate

D. None of these

What is the correct answer?

4

When the fulcrum is in between the load and effort, the lever is said to be of

A. First type

B. Second type

C. Third type

D. Any one of these

What is the correct answer?

4

The circumferential and longitudinal strains in a cylindrical boiler under internal steam pressure are εc and εl respectively. The change in volume of the boiler cylinder per unit volume will be

A. εc + 2εl

B. c + εl

C. εc + εl²

D. εc² + εl

What is the correct answer?

4

When a helical compression spring is cut into halves, the stiffness of the resulting spring will be

A. Same

B. Double

C. One-half

D. One-fourth

What is the correct answer?

4

When screw threads are to be used in a situation where power is being transmitted in one direction only, then the screw threads suitable for this will be

A. Knuckle threads

B. Square threads

C. Acme threads

D. Buttress threads

What is the correct answer?

4

The resilience of a bolt may be increased by

A. Increasing its shank diameter

B. Increasing its length

C. Decreasing its shank diameter

D. Decreasing its length

What is the correct answer?

4

The arms of the pulleys for flat belt drive have

A. Elliptical cross-section

B. Major axis in plane of rotation

C. Major axis twice the minor axis

D. All the three characteristics

What is the correct answer?

4

When the belt is transmitting maximum power, the belt speed should be

A. √(Pmax / 2m)

B. √(Pmax / 3m)

C. √(Pmax / m)

D. √(3m /Pmax) Where m = mass of belt per metre (kg/m) Pmax = maximum permissible tension in belt (N)

What is the correct answer?

4

In a journal bearing, the load on the bearing is __________ to the axis of the journal.

A. Parallel

B. Perpendicular

C. Both A and B

D. None of these

What is the correct answer?

4

The bending moment M and a torque T is applied on a solid circular shaft. If the maximum bending stress equals to maximum shear stress developed, then M is equal to

A. T/2

B. T

C. 2T

D. 4T

What is the correct answer?

4

Basic hole is one

A. Whose upper deviation is zero

B. Whose lower deviation is zero

C. Whose lower as well as upper deviations are zero

D. Does not exist

What is the correct answer?

4

In cylindrical cams, the follower moves

A. In a direction perpendicular to the cam axis

B. In a direction parallel to the cam axis

C. In any direction irrespective of cam axis

D. Along the cam axis

What is the correct answer?

4

The square threads are usually found on

A. Spindles of bench vices

B. Railway carriage couplings

C. Feed mechanism of machine tools

D. Screw cutting lathes

What is the correct answer?

4

When the connected members are very yielding (soft gasket) as compared to the bolt, then the resultant load on the bolt will be equal to the

A. Initial tension

B. External load applied

C. Sum of the initial tension and external load applied

D. Initial tension or external load, whichever is greater

What is the correct answer?

4

In Vickers hardness testing, the pyramid indentor apex is

A. 40°

B. 122°

C. 136°

D. 152°

What is the correct answer?

4

The rivet head used for boiler plate riveting is usually

A. Pan Head

B. Snap head

C. Counter sunk head

D. Conical head

What is the correct answer?

4

A steel containing upto 0.15% carbon is known as

A. Mild steel

B. Dead mild steel

C. Medium carbon steel

D. High carbon steel

What is the correct answer?

4

A V-belt designated as B 4430 LP has

A. 4430 mm as diameter of small pulley

B. 4430 mm as nominal pitch length

C. 4430 mm as diameter of large pulley

D. 4430 mm as centre distance between pulleys

What is the correct answer?

4

In a band and block brake, the ratio of tensions on the tight and slack sides of band is given by (where μ = Coefficient of friction between the blocks and the drum, θ = Semi-angle of each block subtending at the centre of drum, and n = Number of blocks)

A. T₁/T₂ = μθ × n

B. T₁/T₂ = (μθ)n

C. T₁/T₂ = [(1 - μ tanθ)/ (1 + μ tanθ)]n

D. T₁/T₂ = [(1 + μ tanθ)/ (1 - μ tanθ)]n

What is the correct answer?

4

The velocity factor for precision metallic gears cut with high accuracy and operating at velocities upto 20 m/s is equal to

A. 0.75/ (0.75 + √v)

B. 3/ (3 + v)

C. 4.5/ (4.5 + v)

D. 6/ (6 + v)

What is the correct answer?

4

Two closely coiled helical springs with stiffness k₁ and k₂ respectively are connected in series. The stiffness of an equivalent spring is given by

A. (k₁ k₂)/ (k₁ + k₂)

B. (k₁ - k₂)/ (k₁ + k₂)

C. (k₁ + k₂)/ (k₁ k₂)

D. (k₁ - k₂)/ (k₁ k₂)