Home
Current Affairs January 2024

What is the correct answer?

4

If the value of n = 0 in the equation pvn = C, then the process is called

A. Constant volume process

B. Adiabatic process

C. Constant pressure process

D. Isothermal process

Correct Answer :

C. Constant pressure process


Related Questions

What is the correct answer?

4

The calorific value of gaseous fuel is expressed in

A. kJ

B. kJ/kg

C. kJ/m2

D. kJ/m3

What is the correct answer?

4

First law of thermodynamics deals with

A. Conservation of heat

B. Conservation of momentum

C. Conservation of mass

D. Conservation of energy

What is the correct answer?

4

In order to prevent crushing of masonry at the base of the dam, the maximum stress should be __________ the permissible stress of the soil.

A. Equal to

B. Less than

C. More than

D. None of these

What is the correct answer?

4

The thermal efficiency of an ideal gas turbine plant is given by (where r = Pressure ratio)

A. rγ - 1

B. 1 - rγ - 1

C. 1 - (1/r) γ/γ - 1

D. 1 - (1/r) γ - 1/ γ

What is the correct answer?

4

The distance between the centres of the rivets in adjacent rows of zigzag riveted joint is known as

A. Pitch

B. Back pitch

C. Diagonal pitch

D. Diametric pitch

What is the correct answer?

4

For a perfect gas, according to Boyle's law (where p = Absolute pressure, v = Volume, and T = Absolute temperature)

A. p v = constant, if T is kept constant

B. v/T = constant, if p is kept constant

C. p/T = constant, if v is kept constant

D. T/p = constant, if v is kept constant

What is the correct answer?

4

The ratio of elongation in a prismatic bar due to its own weight (W) as compared to another similar bar carrying an additional weight (W) will be

A. 1 : 2

B. 1 : 3

C. 1 : 4

D. 1 : 2.5

What is the correct answer?

4

In order to know whether a column is long or short, we must know its

A. Ultimate shear stress of the column

B. Factor of safety

C. Torque resisting capacity

D. Slenderness ratio

What is the correct answer?

4

A circular shaft fixed at, A has diameter D for half of its length and diameter D/2 over the other half, as shown in the below figure. If the rotation of B relative to A is 0.1 radian, the rotation of C relative to B will be

A. 0.4 radian

B. 0.8 radian

C. 1.6 radian

D. 3.2 radian

What is the correct answer?

4

One kg of ethylene (C2H4) requires 2 kg of oxygen and produces 22/7 kg of carbon dioxide and __________ kg of water or steam.

A. 9/7

B. 11/7

C. 7/4

D. 1/4

What is the correct answer?

4

For same compression ratio and for same heat added

A. Otto cycle is more efficient than Diesel cycle

B. Diesel cycle is more efficient than Otto cycle

C. Efficiency depends on other factors

D. Both Otto and Diesel cycles are equally efficient

What is the correct answer?

4

The unit of energy is S. I. units is

A. Joule (J)

B. Joule metre (Jm)

C. Watt (W)

D. Joule/metre (J/m)

What is the correct answer?

4

A beam which is fixed at one end and free at the other is called

A. Simply supported beam

B. Fixed beam

C. Overhanging beam

D. Cantilever beam

What is the correct answer?

4

The thermodynamic difference between a Rankine cycle working with saturated steam and the Carnot cycle is that

A. Carnot cycle can't work with saturated steam

B. Heat is supplied to water at temperature below the maximum temperature of the cycle

C. A Rankine cycle receives heat at two places

D. Rankine cycle is hypothetical

What is the correct answer?

4

When wood is heated with a limited supply of air to a temperature not less than 280°C, the resulting fuel is

A. Coke

B. Wood charcoal

C. Bituminous coal

D. Briquetted coal

What is the correct answer?

4

Percentage reduction in area performing tensile test on cast iron may be of the order of

A. 50 %

B. 25 %

C. 20 %

D. 30 %

What is the correct answer?

4

Relation between cp and cv is given by (where cp = Specific heat at constant pressure, cv = Specific heat at constant volume, γ = cp/cv, known as adiabatic index, and R = Gas constant)

A. cv/ cp =R

B. cp - cv = R

C. cv = R/ γ-1

D. Both (B) and (C)

What is the correct answer?

4

The extremeties of any diameter on Mohr's circle represent

A. Principal stresses

B. Normal stresses on planes at 45°

C. Shear stresses on planes at 45°

D. Normal and shear stresses on a plane

What is the correct answer?

4

The bending moment of a cantilever beam of length l and carrying a uniformly distributed load of w per unit length is __________ at the fixed end.

A. wl/4

B. wl/2

C. wl

D. wl²/2

What is the correct answer?

4

The relation between Young's modulus (E), shear modulus (C) and bulk modulus (K) is given by

A. E = 3K.C/(3K + C)

B. E = 6K.C/(3K + C)

C. E = 9K.C/(3K + C)

D. E = 12K.C/(3K + C)

What is the correct answer?

4

A riveted joint in which the number otrivets decrease from innermost to outer most rows is called

A. Chain riveted joint

B. Diamond riveted joint

C. Crisscross riveted joint

D. Zigzag riveted joint

What is the correct answer?

4

The ratio of the largest load in a test to the original cross-sectional area of the test piece is called

A. Elastic limit

B. Yield stress

C. Ultimate stress

D. Breaking stress

What is the correct answer?

4

The value of cp/cv for air is

A. 1

B. 1.4

C. 1.45

D. 2.3

What is the correct answer?

4

A material obeys hooks law up to

A. Plastic limit

B. Elastic limit

C. Yield point

D. Limit of proportionality

What is the correct answer?

4

The neutral axis of the cross-section a beam is that axis at which the bending stress is

A. Zero

B. Minimum

C. Maximum

D. Infinity

What is the correct answer?

4

Which of the following cycles is not a reversible cycle?

A. Carnot

B. Ericsson

C. Stirling

D. None of the above

What is the correct answer?

4

Select the correct statement as per Charles' law

A. p.v = constant, if T is kept constant

B. v/T = constant, if p is kept constant

C. p/T = constant, if v is kept constant

D. T/p = constant, if v is kept constant

What is the correct answer?

4

When a rectangular beam is loaded transversely, the maximum compressive stress is developed on the

A. Top layer

B. Bottom layer

C. Neutral axis

D. Every cross-section

What is the correct answer?

4

Which of the following gas is mostly used in town for street and domestic lighting and heating?

A. Producer gas

B. Coal gas

C. Mond gas

D. Coke oven gas

What is the correct answer?

4

The strain energy stored in a solid circular shaft subjected to shear stress (τ), is: (Where G = Modulus of rigidity for the shaft material)

A. τ²/ 2G × Volume of shaft

B. τ/ 2G × Volume of shaft

C. τ²/ 4G × Volume of shaft

D. τ/ 4G × Volume of shaft