Related Questions
What is the correct answer?
4
Parallel straight line pattern of temperature distribution for both hot and cold fluids is observed in case of heat exchanger of the type
A. Parallel flow with equal heat capacities
B. Counter flow with equal heat capacities
C. Counter flow with unequal heat capacities
D. Parallel flow with unequal heat capacities
What is the correct answer?
4
Factor of safety is the ratio of the __________ stress to the working stress.
What is the correct answer?
4
Thermistors are used in __________ devices.
C. Temperature compensating
What is the correct answer?
4
Satellites burn off during re-entry to earth's atmosphere, because of the
B. Gravitational pull by earth
C. Friction with earth's atmosphere
D. Loss in weight of the satellite
What is the correct answer?
4
Gas turbine normally employs a constant __________ cycle.
What is the correct answer?
4
The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be
What is the correct answer?
4
With decrease in the grain size of a material, its creep resistance
D. Either (A) or (B); depends on the material
What is the correct answer?
4
Ganister contains maximum percentage of
What is the correct answer?
4
The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the
A. Ability to absorb shock
B. Capacity to store energy
C. Ratio of the wire & coil diameters
D. Load to produce unit deflection
What is the correct answer?
4
The specific gravity of coal depends mainly on its __________ content.
What is the correct answer?
4
The heat released by cooling one mole of copper from 400 K to room temperature (300 K) is (assume : Cp of copper is 23 J K-1mole-1)
What is the correct answer?
4
Chromium molybdenum steel cannot be welded using __________ welding.
What is the correct answer?
4
Particle nature of cathode rays is proved due to the fact that they
A. Travel in a straight line
B. Get deflected by magnetic electric field
D. Heat the exposed material
What is the correct answer?
4
Glass reacts with
What is the correct answer?
4
Notched bar test is used for testing the __________ of a material.
What is the correct answer?
4
The following type of bonding is strongly directional in solids.
What is the correct answer?
4
What is the percentage of chromium in 18-4-1 high speed steel?
What is the correct answer?
4
Which of the following is resistant to the action of both heat & chemicals?
What is the correct answer?
4
In Imperial Smelting Process for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following:
A. Jet of water at high pressure
C. Mixture of water and air
What is the correct answer?
4
The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it.
What is the correct answer?
4
Larger length & diameter water pipes are made by
A. Electrical resistance welding
C. Semi-centrifugal casting
What is the correct answer?
4
Evaporative cooling process employs a combination of cooling and humidification in which the
A. Sensible heat is added
B. Sensible heat is removed and the latent heat is added
C. Latent heat is removed
D. Sensible heat is added and latent heat is removed
What is the correct answer?
4
In the X-ray radiography technique, the tube voltage for thicker plates as compared to thin plates, should be
A. Higher, as it gives higher wavelength
B. Lower, as it gives higher wavelength
C. Higher, as it gives shorter wavelength
D. Lower, as it gives shorter wavelength
What is the correct answer?
4
Steel balls are manufactured by
What is the correct answer?
4
The ratio of the shear stress to the principal stress on a principal plane is
What is the correct answer?
4
The main charge in blast furnace is usually
C. Limestone, coke & iron ore
D. Limestone, sand & iron ore
What is the correct answer?
4
The swift cup test evaluates the following property of a sheet metal.
What is the correct answer?
4
Propulsion of rocket follows from the
A. Newton's second law of motion
B. Newton's third law of motion
What is the correct answer?
4
Metal shots used in shot blasting are made of
What is the correct answer?
4
Maximum heat dissipation occurs from a steel wire (k = 0.5 W/m. k) of 15 mm diameter exposed to air (h = 20W/m2 .k), when the insulation thickness is __________ mm.