Home
Current Affairs January 2024

What is the correct answer?

4

In a plain milling cutter, the portion of the gash adjacent to the cutting edge on which the chip impinges is called

A. Face

B. Fillet

C. Land

D. Lead

Correct Answer :

A. Face


Related Questions

What is the correct answer?

4

The aluminium oxide abrasive is chiefly used for grinding

A. High speed steel

B. Carbon steel

C. Wrought iron

D. All of these

What is the correct answer?

4

Green sand mould indicates that

A. Polymeric mould has been cured

B. Mould has been totally dried

C. Mould is green in colour

D. Mould contains moisture

What is the correct answer?

4

When the tool moves parallel to the lathe axis, the movement is termed as

A. Cross feed

B. Angular feed

C. Longitudinal feed

D. Any one of these

What is the correct answer?

4

If a gas metal arc process uses a low arc voltage and the arc is continuously interrupted as the molten electrode metal fills up the arc gap is known as

A. ARC

B. Short ARC

C. ARC length

D. ARC blow

What is the correct answer?

4

Gears can be best produced on mass production by

A. Shaping

B. Casting

C. Forming

D. Hobbing

What is the correct answer?

4

The rake angle required to machine brass by high speed steel tool is

A.

B. 10°

C. 20°

D. 100°

What is the correct answer?

4

It is desired to perform the operations like drilling, reaming, counter-boring etc. on a work piece. Which of the following machine will be used?

A. Sensitive drilling machine

B. Radial drilling machine

C. Gang drilling machine

D. Multiple spindle drilling machine

What is the correct answer?

4

Drilling is an example of

A. Orthogonal cutting

B. Oblique cutting

C. Simple cutting

D. Uniform cutting

What is the correct answer?

4

A coarse grained grinding wheel is used to grind

A. Hard and brittle materials

B. Soft and ductile materials

C. Hard and ductile materials

D. Soft and brittle materials

What is the correct answer?

4

For softer materials, the point angle of the drill is kept

A. Equal to 118°

B. Less than 118°

C. More than 118°

D. Any one of these

What is the correct answer?

4

What is the welding defect caused due to improper control and poor removal of slog between passes called?

A. Mismatch

B. Under fill

C. Crack

D. Porosity

What is the correct answer?

4

Gear lapping is an operation

A. After heat treatment

B. Prior to heat treatment

C. For gear reconditioning

D. None of these

What is the correct answer?

4

The increase in depth of cut and feed rate __________ surface finish.

A. Improves

B. Deteriorates

C. Does not effect

D. None of these

What is the correct answer?

4

Two 1 mm thick steel sheets are to be spot welded at a current of 5000 A. Assuming effective resistance to be 200 μm and current flow time of 0.2 second, heat generated during the process will be

A. 0.2 Joule

B. 1 Joule

C. 5 Joule

D. 1000 Joule

What is the correct answer?

4

For turning small taper on long workpiece, the suitable method is

A. By a form tool

B. By setting over the tail stock

C. By a taper turning attachment

D. By swivelling the compound rest

What is the correct answer?

4

The binding material used in cemented carbide tools is

A. Tungsten

B. Chromium

C. Silicon

D. Cobalt

What is the correct answer?

4

Which of the following parameters govern the value of shear angle in continuous chip formation?

A. True feed

B. Chip thickness

C. Rake angle of the cutting tool

D. All of these

What is the correct answer?

4

The swing diameter over the bed is ________ the height of the centre measured from the bed of the lathe.

A. Equal to

B. Twice

C. Thrice

D. One-half

What is the correct answer?

4

In a milling operation, two side milling cutters are mounted with a desired distance between them so that both sides of a workpiece can be milled simultaneously. This set up is called

A. Gang milling

B. Straddle milling

C. String milling

D. Side milling

What is the correct answer?

4

A solid cylinder of diameter 100 mm and height 50 mm is forged between two frictionless flat dies to a height of 25mm. The percentage change in diameter is

A. 0

B. 2.07

C. 20.7

D. 41.4

What is the correct answer?

4

If the tearing efficiency of a riveted joint is 50%, then ratio of rivet hole diameter to the pitch of rivets is

A. 0.20

B. 0.30

C. 0.50

D. 0.60

What is the correct answer?

4

A bottoming tap has

A. Its end tapered for about three or four threads

B. Its end tapered for about eight or ten threads

C. Full threads for the whole of its length

D. None of the above

What is the correct answer?

4

The process of improving the cutting action of the grinding wheel is called

A. Truing

B. Dressing

C. Facing

D. Clearing

What is the correct answer?

4

The grooving is an operation of

A. Bevelling the extreme end of a workpiece

B. Embossing a diamond shaped pattern on the surface of a workpiece

C. Reducing the diameter of a workpiece over a very narrow surface

D. Enlarging the end of a hole cylindrically

What is the correct answer?

4

What is the type of welding defect caused due to poor manipulation of weld rod or a dirty joint called?

A. Porosity

B. Undercut

C. Under fill

D. Crack

What is the correct answer?

4

In centre less grinders, the maximum angular adjustment of the regulating wheel is

A.

B. 10°

C. 15°

D. 20°

What is the correct answer?

4

The saw milling is an operation of

A. Producing grooves around the periphery of a cylindrical or conical workpiece

B. Producing narrow slots or grooves on a workpiece

C. Reproduction of an outline of a template on a workpiece

D. Machining several surfaces of a workpiece simultaneously

What is the correct answer?

4

A dynamometer is a device used for the measurement of

A. Chip thickness ratio

B. Forces during metal cutting

C. Wear of the cutting tool

D. Deflection of the cutting tool

What is the correct answer?

4

In metal machining, the work-tool contact zone is a zone where heat is generated due to

A. Plastic deformation of metal

B. Burnishing friction

C. Friction between the moving chip and the tool face

D. None of the above

What is the correct answer?

4

In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool, the cutting velocity is 90 m/min. The feed is 0.24 mm/rev and the depth of cut is 2mm. The chip thickness obtained is 0.48 mm. If the orthogonal rake angle is zero and the principle cutting edge angle is 90⁰, the shear angle in degree is

A. 20.56

B. 26.56

C. 30.56

D. 36.56