Home
Current Affairs January 2024

What is the correct answer?

4

In centreless grinders, the regulating wheel is inclined at

A. 0° to 8°

B. 9° to 15°

C. 16° to 20°

D. 21° to 25°

Correct Answer :

A. 0° to 8°


Related Questions

What is the correct answer?

4

When two main plates are kept in alignment butting each other and riveted with cover plate on both sides of the main plates with two rows of rivets in each main plate, the joint is known as _______ double cover butt joint.

A. Single riveted

B. Double riveted

C. Both (A) and (B)

D. None of these

What is the correct answer?

4

For generating a Coons surface we require

A. A set of grid points on the surface

B. A set of grid control points

C. Four bounding curves defining the surface

D. Two bounding curves and a set of grid control points

What is the correct answer?

4

When 3-2-1 principle is used to support and locate a three dimensional work-piece during machining, the number of degrees of freedom that are restricted is

A. 7

B. 8

C. 9

D. 10

What is the correct answer?

4

What is the type of shielding gas for GTAW (Gas Tungsten Arc Welding) used for carbon steels only called?

A. Argon H₂

B. Argon CO₂

C. Argon Helium

D. Helium

What is the correct answer?

4

The process of removing metal by a cutter which is rotated in the same direction of travel of workpiece, is called

A. Up milling

B. Down milling

C. Face milling

D. End milling

What is the correct answer?

4

Side relief angle of a single point tool is the angle

A. By which the face of the tool is inclined towards back

B. By which the face of the tool is inclined sideways

C. Between the surface of the flank immediately below the point and a plane at right angles to the centre line of the point of tool

D. Between the surface of the flank immediately below the point and a line drawn from the point perpendicular to the base

What is the correct answer?

4

In ECM, the material removal is due to

A. Corrosion

B. Erosion

C. Fusion

D. Ion displacement

What is the correct answer?

4

The machining of titanium is difficult due to

A. High thermal conductivity of titanium

B. Chemical reaction between tool and work

C. Low tool-chip contact area

D. None of these

What is the correct answer?

4

The type of reamer used for reaming soft aluminium or copper, is

A. Straight fluted reamer

B. Left hand spiral fluted reamer

C. Right hand spiral fluted reamer

D. Any one of these

What is the correct answer?

4

The in-feed grinding is used to

A. Produce tapers

B. Grind shoulders and formed surfaces

C. Grind long, slender shafts or bars

D. All of these

What is the correct answer?

4

Broaching is applied for machining

A. Internal and external surfaces

B. Round or irregular shaped holes

C. External flat and contoured surfaces

D. All of these

What is the correct answer?

4

When the tool moves parallel to the lathe axis, the movement is termed as

A. Cross feed

B. Angular feed

C. Longitudinal feed

D. Any one of these

What is the correct answer?

4

In hot machining, tool is made of

A. Tungsten carbide

B. Brass or copper

C. Diamond

D. Stainless steel

What is the correct answer?

4

The addition of lead, sulphur and phosphorus to low carbon steels, help to

A. Reduce built up edge

B. Break up chips

C. Improve machinability

D. All of these

What is the correct answer?

4

What is the type of welding defect caused due to poor manipulation of weld rod or a dirty joint called?

A. Porosity

B. Undercut

C. Under fill

D. Crack

What is the correct answer?

4

The main purpose of a boring operation, as compared to drilling, is to

A. Drill a hole

B. Finish the drilled hole

C. Correct the hole

D. Enlarge the existing hole

What is the correct answer?

4

Cold working of steel is defined as working

A. At its recrystallisation temperature

B. Above its recrystallisation temperature

C. Below its recrystallisation temperature

D. At two thirds of the melting temperature of the metal

What is the correct answer?

4

The grinding wheel speed (surface speed in m/min) usually varies from

A. 500 to 1000

B. 1000 to 1500

C. 1500 to 2000

D. 2000 to 2500

What is the correct answer?

4

Slow speed of the spindle is necessary in

A. Thread cutting

B. Turning a work of larger diameter

C. Turning a hard or tough material

D. All of these

What is the correct answer?

4

In a CNC program block, N002 GO2 G91 X40 Z40......, GO2 and G91 refer to

A. Circular interpolation in counter clockwise direction and incremental dimension

B. Circular interpolation in counter clockwise direction and absolute dimension

C. Circular interpolation in clockwise direction and incremental dimension

D. Circular interpolation in clockwise direction and absolute dimension

What is the correct answer?

4

Green sand mould indicates that

A. Polymeric mould has been cured

B. Mould has been totally dried

C. Mould is green in colour

D. Mould contains moisture

What is the correct answer?

4

Two plates of the same metal having equal thickness are to be butt welded with electric arc. When the plate thickness changes, welding is achieved by

A. Adjusting the current

B. Adjusting the duration of current

C. Changing the electrode size

D. Changing the electrode coating

What is the correct answer?

4

A right hand tool on a lathe cuts most efficiently when it travels

A. From left to right end of the lathe bed

B. From right to left end of the lathe bed

C. With the help of a compound slide

D. Across the bed

What is the correct answer?

4

Buffing wheels are made of

A. Softer metals

B. Cotton fabric

C. Carbon

D. Graphite

What is the correct answer?

4

A hole is of dimension φ = 9 ₊0⁺⁰⁰¹⁵ mm. The corresponding shaft is of dimension φ = 9 ₊0.001⁺⁰⁰¹⁰ mm. The resulting assembly has

A. Loose running fit

B. Close running fit

C. Transition fit

D. Interference fit

What is the correct answer?

4

The broaching operation in which either the work or the tool moves across the other, is known as

A. Pull broaching

B. Push broaching

C. Surface broaching

D. Continuous broaching

What is the correct answer?

4

Match the items of List-I (Equipment) with the items of List-II (Process) and select the correct answer using the given codes.
List-I (Equipment)List-II (Process)
P. Hot Chamber Machine1. Cleaning
Q. Muller2. Core making
R. Dielectric Baker3. Die casting
S. Sand Blaster4. Annealing
.5. Sand mixing

A. P-2, Q-1, R-4, S-5

B. P-4, Q-2, R-3, S-5

C. P-4, Q-5, R-1, S-2

D. P-3, Q-5, R-2, S-1

What is the correct answer?

4

The cutting speed for counter-boring should be _________ that of drilling operation.

A. Equal to

B. Less than

C. Greater than

D. None of these

What is the correct answer?

4

The chamfering is an essential operation after

A. Knurling

B. Rough turning

C. Boring

D. Thread cutting

What is the correct answer?

4

In machining metal, cutting force at the cutting edge is measured by a

A. Wattmeter

B. Dynamometer

C. Hydrometer

D. Pyrometer