Related Questions
What is the correct answer?
4
Architectural dimensioning is usually done in ________.
What is the correct answer?
4
This material is used in masonry construction, most commonly for ornamental facing:
What is the correct answer?
4
When lettering a CAD drawing, for clarity you should limit the number of fonts to:
What is the correct answer?
4
This is the plane upon which the top view is projected:
What is the correct answer?
4
This is the measured size of a finished part:
What is the correct answer?
4
Elevation drawings will include information about ________.
What is the correct answer?
4
Center lines are used to locate or represent the centers of ________.
What is the correct answer?
4
The foundation contractor will work with the following architectural plans.
What is the correct answer?
4
Architectural drawings used to construct a house are often plotted with a scale of ¼ = 1'-0. What scale is this?
What is the correct answer?
4
This means that a feature of a finished product contains the maximum amount of material permitted by the tolerance dimensions for that feature:
A. Maximum material condition
B. Machined material condition
C. Maximum machined indication
D. Machine mark indication
What is the correct answer?
4
This type of circuit is a semiconductor wafer or chip:
What is the correct answer?
4
When filling an area with a hatch pattern in Auto-CAD the drafter needs to be able to ________.
A. See the entire bounding area to hatch
D. Set the layer to Defpoints
What is the correct answer?
4
In order to convert fractional inches into decimal inches ________.
A. Look on a metric conversion chart
B. Divide the numerator (top number) by the denominator (bottom number)
C. Check the engineer's scale
What is the correct answer?
4
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
C. Block Definition Dialog
What is the correct answer?
4
An architect often relies on a ________ to complete the set of technical drawings used in the design of an office building.
D. Construction superintendent
What is the correct answer?
4
When using the descriptive geometry method to create an auxiliary view the drafter should __________.
A. Rotate the snap grid to the same angle of the inclined plane
B. Offset the right vertical line of the front view
C. Rotate the top line of the front view 45 degrees
D. Offset the top line of the front view 2 inches
What is the correct answer?
4
This is a flat or rounded tab protruding from a surface, usually to provide a method for attachment:
What is the correct answer?
4
When drawing a line using the relative coordinate system a line is created from ________.
B. The ending point of the last line
C. The beginning point of the last line
What is the correct answer?
4
Once a drawing is determined to be complete, the title block is used to document the change from:
A. A draft to a finished drawing
B. A finished to a working drawing
C. An assembly to a finished drawing
D. A working drawing to a draft
What is the correct answer?
4
Baseline dimensions are referenced from a common geometric feature known as a ________.
What is the correct answer?
4
This type of axonometric drawing has equal foreshortening along two axis directions and a different amount on the third axis:
What is the correct answer?
4
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
What is the correct answer?
4
The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section.
What is the correct answer?
4
This is a rounded exterior blend between surfaces:
What is the correct answer?
4
Referring to the fractional inches to decimal inches to millimetre conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
What is the correct answer?
4
In this type of dimensioning, allowance must be made for bends:
What is the correct answer?
4
The ________ dimension tool will place the length of an angled line.
What is the correct answer?
4
PDM is the acronym for:
A. Project drawing management
B. Product drawing manipulation
C. Product data management
D. Project data manipulation
What is the correct answer?
4
The Offset tool should only be used for placing ________ in an isometric drawing.
What is the correct answer?
4
In this type of drawing, vertical pipes may be revolved into the horizontal plane: