In oblique sketches, the most commonly used angles for receding lines are:
15 or 30 degrees
25 or 30 degrees
30 or 45 degrees
45 or 60 degrees
Correct Answer :
C. 30 or 45 degrees
Related Questions
This is the theoretically exact size from which limits of size are determined:
Actual Size
Dimensioned size
Production size
Basic size
This is a curve showing the displacement of the follower as ordinates on a base line that represents one revolution of the cam:
Displacement diagram
Follower
Cam cycle
Reciprocation chart
These maps are used in planning installations of trees, shrubbery, drives, and other garden features:
Landscape maps
Engineering maps
Topographic maps
Cadastral maps
These types of projectors converge at a vanishing point:
Perspective
Parallel
Orthographic
Oblique
In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:
Removed section
Revolved section
Auxiliary section
Partial section
The foundation contractor will work with the following architectural plans.
Foundation
Site plan
Floor plan
All of the above
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
Grid
Block Text Box
Block Definition Dialog
None of the above
Switches and relays should be shown in this position with no operating force or applied energy:
Normal
Closed
Offset
Application
This type of thread is a thread on the inside of a member:
Basic thread
External thread
Internal thread
Major diameter thread
The building construction industry relies on sets of ________ drawings to construct homes and commercial buildings.
Mechanical
Isometric
Architectural working
All of the above
In oblique projection, important shapes should be in this position relative to the viewing plane:
Parallel
Perpendicular
Adjacent
Rotated
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
Sidewalk
Roof overhang
Plumbing drain lines
None of the above
This type of solid has a polygon for a base and triangular lateral faces that intersect at a vertex:
Pyramid
Prism
Cone
Torus
The thread note for a typical bolt will include the ________.
Major diameter of the thread
Material
Center line
Offset distance
This is formed where three or more surfaces intersect:
Oblique
Line
Edge
Vertex
Once the architect has finalized the house plans with the client any changes to the design requested by the client will require a ________.
Change order
Modification slip
Whole new set of drawings
None of the above
Lines of an isometric drawing that are not parallel to the isometric axes are called this:
Trimetric lines
Non-isometric lines
Multiview lines
Dimetric lines
The bounding box method for setting up an isometric drawing helps the drafter ________.
Confine the isometric drawing to its maximum size
Figure what lines are to be illustrated vertical and horizontal
Position the isometric drawing in paper space
None of the above
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
Dimension line
Extension line
Leader
Specification
If a plane is parallel to the plane of projection, it appears:
True size
As a line or edge
Foreshortened
As an oblique surface
In the section view, the areas that would have been in actual contact with the cutting plane are shown with:
A cutting plane line
Section lining
Visible lines
Lines and arrows
In offset sections, offsets or bends in the cutting plane are all:
90 degrees
180 degrees
Either 90 or 180 degrees
30, 60 or 90 degrees
The principle views associated with orthographic projection are ________.
Front view
Right side view
Top view
All of the above
These units are based on inch-foot and yard measurements:
International customary units
U.S. metric units
U.S. customary units
ISO international units
A round is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
In working drawings, these show all necessary information not given directly on the drawing with its dimensions and notes:
Document strips
Portable documents
Formatting forms
Title and record strips
Spur gear design normally begins with selecting this:
Rack size
Tooth size
Gear size
Pitch diameter
If designs require changes, they should be documented with:
Development plans
Product proposals
Document reviews
Engineering change orders
Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for________.
Circle templates
Triangles
Technical pens
Lettering guides
The dimension text size is determined by what the architect deems necessary in __________.
Model space
Paper space
The Finished plot
The PDF file