Home
Current Affairs January 2024

What is the correct answer?

4

In practice, the compression ratio of compression-ignition (CI) engine ranges from

A. 15 to 25

B. 5 to 10

C. 40 to 55

D. 60 to 70

Correct Answer :

A. 15 to 25


Related Questions

What is the correct answer?

4

Which of the following is preferred for riveting?

A. Lap joint

B. Butt joint

C. Either (A) or (B)

D. Neither (A) nor (B)

What is the correct answer?

4

Hot extrusion process is not used for making

A. Cast iron pipe for domestic water supply

B. Aluminium curtain rods

C. Stainless steel tubes used in furnitures

D. Any of these

What is the correct answer?

4

An ideal material for making cooking vessels should have

A. High heat capacity

B. Low heat capacity

C. High thermal conductivity

D. Both (B) and (C)

What is the correct answer?

4

Heat flow across a hollow sphere of inner radius 'r1' and outer radius 'r2' is directly proportional to

A. (r2 - r1)/r1. r2

B. r1. r2/(r2 - r1)

C. (r2 + r1)/r1. r2

D. r1. r2/(r2 + r1)

What is the correct answer?

4

__________ is the hardest material out of the following.

A. Boron carbide

B. Tungsten carbide

C. Hardened steel

D. Silicon carbide

What is the correct answer?

4

Brittleness induced due to the presence of sulphur in steel can be reduced by adding

A. Manganese

B. Magnesium

C. Vanadium

D. Copper

What is the correct answer?

4

Which of the following material handling equipments is not suitable for moving materials in varying paths?

A. Hand trolley

B. Belt conveyor

C. Crane

D. Truck

What is the correct answer?

4

The approximate height of a blast furnace having a useful volume of 2000 m3 is about __________ metres

A. 25

B. 35

C. 55

D. 75

What is the correct answer?

4

The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm.

A. 0.5

B. 3

C. 10

D. 25

What is the correct answer?

4

Cold chisels hammers are made of

A. High speed steel

B. High carbon steel

C. Forged steel

D. Mild steel

What is the correct answer?

4

Use of flux during soldering is done to

A. Increase fluidity of solder by lowering its melting temperature

B. Prevent oxide formation

C. Wash away surplus solder

D. Full up the joint gap

What is the correct answer?

4

For the Stoke's law to be valid in the case of a falling sphere in a fluid, the

A. Reynolds number (based on sphere diameter) should be < 1

B. Flow around the sphere should be in turbulent region

C. Sphere must be metallic

D. Fluid density should be constant

What is the correct answer?

4

Factor of safety in machine design is defined as the ratio of ultimate stress to __________ stress.

A. Working

B. Bearing

C. Yield

D. None of these

What is the correct answer?

4

Energy of the sun arises mainly from __________ reactions.

A. Fusion

B. Fission

C. Combustion

D. None of these

What is the correct answer?

4

A solid aluminium ball, when quenched in a water bath maintained at 40°C, cools down from 550°C to 450°C in 20 seconds. The expected temperature of the ball after next 20 seconds may be about __________ °C.

A. 370

B. 340

C. 320

D. 300

What is the correct answer?

4

Two solutions A1 & A2 have pH value of 2 & 6 respectively. It implies that the solution

A. A1 is more alkaline than solution A2

B. A1 is highly acidic

C. A2 is very slightly acidic

D. Both (B) & (C)

What is the correct answer?

4

Potable water means the water used for

A. Fire-fighting

B. Cooling

C. Drinking

D. Evaporation to produce steam

What is the correct answer?

4

Metal cutting by oxy-acetylene flame is accomplished by the __________ of the metal.

A. Burning

B. Intensive oxidation

C. Evaporation

D. None of these

What is the correct answer?

4

The transition temperature at which all the ferromagnetic materials become paramagnetic materials is termed as the 'Curie temperature'. Its value for cobalt is __________ °C.

A. 768

B. 1127

C. 1359

D. 1480

What is the correct answer?

4

Metalloids

A. Are good conductor of heat & electricity

B. Act as electron donors with metals & as electron acceptor with non-metals

C. Are not necessarily solids at room temperature

D. Are compounds that exhibit both metallic & non-metallic properties to some extent and are exemplified by elements like germanium, silicon & boron

What is the correct answer?

4

Use of economiser in a boiler plant reduces the fuel consumption for steam generation by about __________ percent.

A. 1

B. 10

C. 30

D. 50

What is the correct answer?

4

The capacity of a spring to store energy is called the spring form co-efficient. Stiffness of a spring is measured by the

A. Ability to absorb shock

B. Capacity to store energy

C. Ratio of the wire & coil diameters

D. Load to produce unit deflection

What is the correct answer?

4

The only suitable method for hardening the low carbon steel is case hardening. Which of the following is a case hardening process?

A. Cyaniding

B. Sherardizing

C. Spheroidising

D. None of these

What is the correct answer?

4

Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.

A. Horizontal

B. Vertical

C. Inclined

D. Any

What is the correct answer?

4

Oxide layer formed on the non-ferrous metal surface after its annealing is

A. Removed by acid pickling

B. Hammered into the surface

C. Removed with coarse emery cloth

D. Left as such to protect the surface

What is the correct answer?

4

A reduction in thermal resistance during heat transfer does not occur in the

A. Convection heat transfer by stirring the fluid and cleaning the heating surface

B. Conduction heat transfer by reduction in the material thickness and increase in the thermal conductivity

C. Radiation heat transfer by increasing the temperature and reducing the emissivity

D. None of these

What is the correct answer?

4

Titanium is produced by __________ of Ti Cl4.

A. Electrolytic reduction

B. Calcium reduction

C. Magnesium reduction

D. Thermal dissociation

What is the correct answer?

4

The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.

A. Casting

B. Pattern

C. Draft

D. Distortion

What is the correct answer?

4

Vernier calipers cannot be used to measure the

A. I.D. & O.D. of the shaft

B. Thickness of parts

C. Depth of holes

D. Clearance between two mating surfaces

What is the correct answer?

4

Ferromagnetic materials owe their properties to __________ inner sub-shells.

A. Completely filled

B. Partially filled

C. Equally filled

D. Vacant