Related Questions
What is the correct answer?
4
For a series ACcircuita ___ is not used as a reference phasor.
What is the correct answer?
4
Kirchhoff�s laws (KCL and KVL) are applicable to
C. DC as well as AC circuits
D. Passive networks alone
What is the correct answer?
4
In calculating maximum instantaneous power ___ voltage or current is used.
What is the correct answer?
4
A law which states that when a constant electromotive force is applied to a circuit consisting of a resistor and capacitor connected in seriesa the time taken for the potential on the plates of the capacitor to rise to any given fraction of its final value depends only on the product of capacitance and resistance.
What is the correct answer?
4
For a linear circuita ___ voltage or current is used to calculate average power.
What is the correct answer?
4
Under the conditions of maximum power transfera a voltage source is delivering a power of 15 W to the load. What is the power generated by the source?
What is the correct answer?
4
Delta to wye or wye to delta transformation technique is applied to a ___ network.
What is the correct answer?
4
Refers specifically to steady state values of quantities in ac circuits which are complex numbers.
What is the correct answer?
4
And ideal current source has an internal conductance of _____ siem
What is the correct answer?
4
For a triangular and sawtooth waveform the rms voltage or current equals
B. 0.577 times peak value
C. 0.577times average value
What is the correct answer?
4
The average value of a triangular or sawtooth wave is _____ times its peak value.
What is the correct answer?
4
A three-by-threea series-parallel matrix of resistorsa all having the same ohmic valuea would have a net resistance of
A. One-third the value of a single resistor
B. Three times the value of a single resistor
C. The same value as a single resistor
D. Nine times the value of a single resistor
What is the correct answer?
4
The wavelength of an alternating waveform depends upon the ___ of the variation.
What is the correct answer?
4
³Any resistance R in a branch of a network in which a current I is flowing can be replaced by a voltage equal to IR�. This states
What is the correct answer?
4
Which of the following is a preferred resistor value?
What is the correct answer?
4
An open resistor when checked with an ohmmeter reads
C. High but within the tolerance
What is the correct answer?
4
In a series RLCcircuit
A. Increasing the frequency decreases the resistance
B. Increasing the frequency increases the resistance
C. Both XLand XCchange as frequency changes
D. Impedance will always decrease
What is the correct answer?
4
What is the conductance of a circuit having three 10 resistors in parallel?
What is the correct answer?
4
In an ac wavea 30 degrees of phase is ___ of a cycle.
What is the correct answer?
4
Parallel resonant circuit is sometimes called as
What is the correct answer?
4
The resistance of an insulator ___ when its temperature is increased.
What is the correct answer?
4
The unit of elastance is
What is the correct answer?
4
Which of the following is the peakiest?
What is the correct answer?
4
The second strip of an electronic resistor color-code represents
B. The second digit of the value
What is the correct answer?
4
A circuit whose parameters change with voltage or current.
What is the correct answer?
4
If one resistance in a series connection is opena then
A. The current is zero in all the other resistances
B. The current is maximum in all the other resistances
C. The voltage is zero across the open resistance
D. The voltage is infinite across the open resistance
What is the correct answer?
4
An intermittent and non-symmetrical alternating current like that obtained from the secondary winding of an induction coil
What is the correct answer?
4
What is a rotating vector whose projection can represent either current or voltage in an ac circuit?
What is the correct answer?
4
What is the other name of relative permittivity?
D. Specific inductance capacity
What is the correct answer?
4
The value of temperature coefficient ( ) is dependent upon
A. The nature of material and temperature
B. The length of material
C. The cross-sectional area of the material
D. The volume of the material