Related Questions
What is the correct answer?
4
Steel produced from phosphatic iron is __________ in nature.
What is the correct answer?
4
Transformer cores are normally made from
C. Grain oriented Fe-Si alloy
What is the correct answer?
4
Which of the following contributes maximum as main source of sulphur in the blast furnace charge?
What is the correct answer?
4
Which of the following metals reacts violently with water?
What is the correct answer?
4
Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is
What is the correct answer?
4
__________ stress cannot be sustained by a fluid in equilibrium.
What is the correct answer?
4
'Ice point' is designated on Fahrenheit temperature scale by
What is the correct answer?
4
The value of for air & most common gases can be safely assumed to be
What is the correct answer?
4
Resilience of a bolt can be increased by increasing its
What is the correct answer?
4
Main constituent of bone ash is
What is the correct answer?
4
Wrought iron is never shaped by
What is the correct answer?
4
Vernier calipers cannot be used to measure the
A. I.D. & O.D. of the shaft
D. Clearance between two mating surfaces
What is the correct answer?
4
Which of the following test is used for distinguishing among dry oils, semi-drying oils and non drying oils?
B. Reichert-Meissl value test
What is the correct answer?
4
The most abundant metal present in the earth's crust is;
What is the correct answer?
4
Which of the, following is not associated with the functioning of a petrol engine?
A. Compression ignition system
What is the correct answer?
4
Age hardening is connected with
What is the correct answer?
4
Brinell Hardness Number (BHN) for talc is approximately in the range of
What is the correct answer?
4
Yield strength of a material is determined by the __________ test.
What is the correct answer?
4
Addition of __________ to steel does not impart hardness.
What is the correct answer?
4
Dislocations are __________ defects.
What is the correct answer?
4
The dimensional formula of bulk modulus of elasticity is same as that of the
What is the correct answer?
4
Which of the following hardness tests does not measure the indentation hardness of metals and alloys?
B. Shore scleroscope test
D. Rockwell hardness test
What is the correct answer?
4
The kinematic viscosity (in stoke) and the absolute/dynamic viscosity (in poise) are the same for __________ at room temperature.
What is the correct answer?
4
Spark plug is provided in a/an
A. Engine having carburettor
C. Compression ignition engine
What is the correct answer?
4
Elimination of brittleness resulting from welding of saw blades is done by __________ of the welded portion.
What is the correct answer?
4
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by
What is the correct answer?
4
Which of the following is not a charge material for cupola?
What is the correct answer?
4
In condensers used in thermal power plants, steam is normally used in shell side and cooling water on the tube side, because of the reason that
A. Compared to the mass flow rate of cooling water, the rate of condensation of steam is invariably smaller
B. Maintaining vacuum on tube side is more difficult than that on the shell side
C. Water velocity can be increased conveniently to increase the overall heat transfer co-efficient because of its lower specific volume compared to steam
D. Condenser can act as a storage unit for condensed steam
What is the correct answer?
4
The fugacity of liquid water at 298 K is approximately 3171 Pa. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be
What is the correct answer?
4
Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively.