Related Questions
What is the correct answer?
4
Referring to the periodic table of elements, it is found that with increasing atomic number. The atomic size in the same
What is the correct answer?
4
Shampoos are commercially not available in the form of
What is the correct answer?
4
Fibrous fracture is normally encountered in the __________ materials.
What is the correct answer?
4
Silicon percentage in silicon steel used for electrical equipments is about
What is the correct answer?
4
Air standard Otto cycle is more efficient than the diesel cycle for the same
A. Heat addition & compression ratio
B. Heat addition & pressure
C. Compression ratio & pressure
D. Cylinder dimension & rpm
What is the correct answer?
4
The order of a chemical reaction
A. Can be determined only experimentally
B. Can be determined from the stoichiometry of the reaction
What is the correct answer?
4
__________ of austenite decreases the hardenability in steel.
D. Dissolved elements (except cobalt)
What is the correct answer?
4
Hot working of lead is carried out at
What is the correct answer?
4
On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is
What is the correct answer?
4
Heat flow across a hollow sphere of inner radius 'r1' and outer radius 'r2' is directly proportional to
What is the correct answer?
4
__________ has a negative co-efficient of linear expansion.
What is the correct answer?
4
Hot extrusion process is not used for making
A. Cast iron pipe for domestic water supply
B. Aluminium curtain rods
C. Stainless steel tubes used in furnitures
What is the correct answer?
4
Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process?
What is the correct answer?
4
Which of the following phenomenon/ phenomena is/are diffusion controlled?
What is the correct answer?
4
Sand used to stop the green sand from sticking to the pattern is termed as the __________ sand.
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
Percentage of argon (by volume) in dry atmospheric air is about
What is the correct answer?
4
Runge-Kutta method is used to solve a/an
A. Ordinary differential equation of nth order
B. Simultaneous non-linear equation
C. Linear differential equation
What is the correct answer?
4
Limestone is added in the blast furnace (during pig iron manufacture) to
A. Form slag by combining with impurities
B. Supply heat by undergoing exothermic reaction with impurities
C. Reduce the coke consumption
What is the correct answer?
4
Fire refining process is employed in case of
What is the correct answer?
4
The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge)
What is the correct answer?
4
The kinematic viscosity (in stoke) and the absolute/dynamic viscosity (in poise) are the same for __________ at room temperature.
What is the correct answer?
4
Carnot cycle is also termed as the constant __________ cycle in thermodynamics.
What is the correct answer?
4
An alloy of Fe - 0.4 % C is
What is the correct answer?
4
Strain hardening effect in metals subjected to cold working is due to the __________ mechanism.
What is the correct answer?
4
Propulsion of rocket follows from the
A. Newton's second law of motion
B. Newton's third law of motion
What is the correct answer?
4
An example of unsteady non uniform flow is the flow of liquid under pressure through a
A. Tapering pipe at constant flow rate
B. Tapering pipe at either decreasing or increasing flow rate
C. Long pipeline of constant diameter
What is the correct answer?
4
Out of the following, which will fracture most readity, when hit with a hard hammer?
What is the correct answer?
4
Which of the following is not categorised as the ore agglomeration process?
What is the correct answer?
4
Theoretical volume of oxygen required for complete combustion of 1Nm3 of acetylene, in oxyacetylene welding is __________ Nm3.