Related Questions
What is the correct answer?
4
The most suitable material for die casting is
What is the correct answer?
4
The main charge in blast furnace is usually
C. Limestone, coke & iron ore
D. Limestone, sand & iron ore
What is the correct answer?
4
Silicon in steel
A. Makes it usable in almost all magnetic circuits where alternating current is used
B. Increases its electrical resistivity and decreases the hysteresis loss
C. Is present upto 5% & 4% respectively when used in transformers & motor armatures
What is the correct answer?
4
Thermit welding uses the following energy source.
C. Energy of high velocity electrons
D. Heat generated by friction
What is the correct answer?
4
Which of the following is a commonly used manometric liquid for low pressure range?
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
If a solid is compressed adiabatically in its elastic range, its __________ remains constant
What is the correct answer?
4
Spark plug is provided in a/an
A. Engine having carburettor
C. Compression ignition engine
What is the correct answer?
4
The starting of a car takes time in winter, because the
A. Octane number of fuel is decreased
B. Fuel supply for ignition is not sufficient
C. Vaporisation of the fuel is decreased
D. Pour point of fuel decreases
What is the correct answer?
4
Air standard Otto cycle is more efficient than the diesel cycle for the same
A. Heat addition & compression ratio
B. Heat addition & pressure
C. Compression ratio & pressure
D. Cylinder dimension & rpm
What is the correct answer?
4
__________ joint is usually used for joining cast iron pipes mostly used for temporary pipelines, where it may be necessary to dismantle & reassemble the pipeline very frequently.
What is the correct answer?
4
Factor of safety in machine design is defined as the ratio of ultimate stress to __________ stress.
What is the correct answer?
4
In the X-ray radiography technique, the tube voltage for thicker plates as compared to thin plates, should be
A. Higher, as it gives higher wavelength
B. Lower, as it gives higher wavelength
C. Higher, as it gives shorter wavelength
D. Lower, as it gives shorter wavelength
What is the correct answer?
4
Euler number is defined as the ratio of inertia force to __________ force.
What is the correct answer?
4
The fugacity of liquid water at 298 K is approximately 3171 Pa. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be
What is the correct answer?
4
Blasting of tri-nitro-toluene (TNT) is done by mixing it with ammonium
What is the correct answer?
4
Hot dipping process is used for coating a low melting point metal (e.g. Pb, Sn, Zn) on iron, steel & copper having relatively higher melting points. Which of the following is not a hot dipping process?
What is the correct answer?
4
Ammonia gas can be dried by
What is the correct answer?
4
Which of the following if present in iron ore, enhances its value?
What is the correct answer?
4
Angular displacement can be measured suitably by a
B. Linear variable differential transducer (LVDT)
What is the correct answer?
4
In an amorphous material, atoms defy any definite atomic structure and exist in random pattern just like in liquid. Which of the following is an amorphous material?
What is the correct answer?
4
__________ pipe is the most suitable for carrying sanitary drainage.
B. Reinforced cement concrete
What is the correct answer?
4
Drossing is a __________ operation.
What is the correct answer?
4
Machinability of hard alloys and tool steels is improved by
What is the correct answer?
4
The __________ of a double acting reciprocating pump as compared to the single acting pump will be almost double.
What is the correct answer?
4
Which of the following materials has the maximum shrinkage allowance?
What is the correct answer?
4
__________ furnace is generally used in the non-ferrous foundries.
What is the correct answer?
4
Latent heat of dry steam at atmospheric pressure is 539 Kcal/kg; which __________ with increase in the pressure of steam.
D. May increase or decrease
What is the correct answer?
4
Work hardenable alloy steel used to make the bucket wheel excavators, blades of bulldozers and other earth moving equipments contain iron, carbon and
What is the correct answer?
4
The cathode in an electrochemical cell always carries
D. Positive or negative charge depending upon the nature of the cell