Related Questions
What is the correct answer?
4
Speed of a submarine in deep sea & that of an aeroplane is measured by a/an
What is the correct answer?
4
Fire refining process is employed in case of
What is the correct answer?
4
Principal alloying elements of cast tool alloys which have very high wear resistance & high temperature strength are
A. Cobalt, chromium & tungsten
B. Cobalt, chromium & nickel
C. Molybdenum, tungsten & chromium
D. Cobalt, zirconium & molybdenum
What is the correct answer?
4
Tempering of a material does not improve its
What is the correct answer?
4
Energy to be supplied to the radioactive nucleus for the emission of a neutron is __________ MeV.
What is the correct answer?
4
Strain hardening effect in metals subjected to cold working is due to the __________ mechanism.
What is the correct answer?
4
Maximum permissible air velocity in pipelines is about __________ metre/second.
What is the correct answer?
4
Cupola produces __________ iron.
What is the correct answer?
4
Temper brittleness of a material can be fairly detected by the __________ test.
What is the correct answer?
4
Suitability of steel for its use in cable is judged by its strength in
What is the correct answer?
4
The best lubricants for a machine working at high temperature & load is
What is the correct answer?
4
Pick out the wrong statement about nucleate boiling.
A. Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface
B. Surface temperature is greater than the saturation temperature of the liquid
C. Heat transfer from the surface of the liquid is less than that in film boiling
D. The temperature is less than that of film boiling
What is the correct answer?
4
Tin based white metals are used, where bearings are subjected to
What is the correct answer?
4
Brittleness induced due to the presence of sulphur in steel can be reduced by adding
What is the correct answer?
4
Work done by a/an __________ process is determined by ∫p. dv
What is the correct answer?
4
Bad odour in sanitary latrines is reduced by periodically sprinkling
What is the correct answer?
4
Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA)?
What is the correct answer?
4
Current employed in resistance welding ranges from __________ kVA/.
What is the correct answer?
4
Mho's scale of hardness, which consists of 10 standard minerals is used for the measurement of __________ hardness.
What is the correct answer?
4
Pressure exerted by a liquid depends upon its
What is the correct answer?
4
Which of the following emissions in the exhaust gas of an I.C. engine causes the formation of photochemical smog?
What is the correct answer?
4
Cemented carbide tools are not suitable for cutting
What is the correct answer?
4
Nusselt number is related to the Reynolds number (Re) in turbulent & laminar flow respectively as
What is the correct answer?
4
Otto cycle used in spark ignition petrol engines is also known as the constant __________ cycle.
What is the correct answer?
4
Which of the following fastening devices has its both ends threaded?
What is the correct answer?
4
For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by
What is the correct answer?
4
Pick out the wrong statement about the machinability of metals. Machinability of a metal
A. Decreases with increase in strain hardening tendencies
B. Decreases with increase in hardness, in general
C. Depend on the composition, microstructure and physical & mechanical properties
D. Decreases with increases in tensile strength & decrease in grain size
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
Fatigue resistance of a material is measured by the
B. Ultimate tensile strength
What is the correct answer?
4
Which of the following is a commonly used manometric liquid for low pressure range?