Home
Current Affairs January 2024

What is the correct answer?

4

__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength.

A. Lancing

B. Shot peening

C. Slugging

D. Spinning

Correct Answer :

B. Shot peening


Related Questions

What is the correct answer?

4

Hot extrusion of aluminium is done in the temperature range of __________ °C.

A. 550-600

B. 450-500

C. 350-400

D. 250-300

What is the correct answer?

4

Which one of the following is incombustible?

A. H2

B. CCl4

C. C2H2

D. S

What is the correct answer?

4

Which of the following mainly decides the current to be employed is arc welding?

A. Electrode size

B. Plate thickness

C. Voltage across the arc

D. Welded portion length

What is the correct answer?

4

Faraday's law of electrolysis is related to the

A. Cation speed

B. Atomic number of the cation

C. Equivalent mass of the electrolyte

D. None of these

What is the correct answer?

4

Mild steel has __________ crystal lattice structure.

A. Face centred cubic (fcc)

B. Body centred cubic (bcc)

C. Orthorhombic

D. Cubic

What is the correct answer?

4

Air standard Otto cycle is more efficient than the diesel cycle for the same

A. Heat addition & compression ratio

B. Heat addition & pressure

C. Compression ratio & pressure

D. Cylinder dimension & rpm

What is the correct answer?

4

High endurance limit of carburised machine parts is because of the fact that carburisation

A. Suppresses any stress concentration produced in the parts

B. Enhances the yield point of the material

C. Introduces a compressive layer on the surface

D. Produces a better surface finish

What is the correct answer?

4

__________ are normally subjected to sub-zero treatment.

A. Highly stressed parts

B. Gauges or precision parts

C. Cold rolled sheets

D. Non machinable materials

What is the correct answer?

4

The softness or hardness of a grinding wheel depends upon the type & amount of bonding material used. For general purpose cutter grinding __________ grinding wheel is normally used.

A. Hard

B. Soft

C. Silicon carbide

D. Aluminium oxide

What is the correct answer?

4

Friction factor for fluid flow in pipe does not depend upon the

A. Pipe length

B. Pipe roughness

C. Fluid density & viscosity

D. Mass flow rate of fluid

What is the correct answer?

4

The cathode in an electrochemical cell always carries

A. Negative charge

B. Positive charge

C. Zero charge

D. Positive or negative charge depending upon the nature of the cell

What is the correct answer?

4

During sensible cooling of air, its wet bulb temperature

A. Decreases but dew point remains constant

B. Increases but dew point remains constant

C. Increases & the dew point decreases

D. Decreases & the dew point increases

What is the correct answer?

4

A cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is

A. 0

B. 0.33

C. 0.44

D. 0.25

What is the correct answer?

4

Pick out the wrong statement.

A. Complete unity of command exists in a line organisation

B. Line organisation is net suitable for expansion and growth of an industry

C. In line and staff organisation, line executes and staff directs

D. None of these

What is the correct answer?

4

Pick out the correct combination about the role of various additives used in polymers.

A. Plasticiser: increases the polymer strength

B. Heat stabiliser: increases the maximum service temperature

C. Fillers: Does not affect the property of polymer but increases its weight

D. Lubricants: increases the flexibility of polymers

What is the correct answer?

4

Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling.

A. Film

B. Nucleate

C. Transition

D. All modes of

What is the correct answer?

4

Catalyst used in the 'catalytic converter' employed in automobile exhaust line for complete combustion/oxidation of carbon monoxide, nitrogen oxides and hydrocarbons is

A. Alumina

B. Platinum

C. Vanadium pentoxide

D. Iron oxide

What is the correct answer?

4

Strain hardening effect in a metal subjected to cold working is due to the __________ mechanism.

A. Fracture

B. Dislocation

C. Slip

D. Twinning

What is the correct answer?

4

Diffusion co-efficient of a metal in a solid solution depends upon its

A. Composition

B. Temperature

C. Both (A) & (B)

D. Neither (A) nor (B)

What is the correct answer?

4

Pick out the wrong statement.

A. For a pressure vessel to be classified as 'thin vessel', the ratio of wall thickness to mean radius is less than 0.1

B. For calculating forces and efficiency of riveted joint, either rivet diameter or rivet hole diameter is used in case of pressure vessel and in structural work

C. Longitudinal joint is normally made butt joint to maintain the circularity of the vessel

D. Maximum diameter of the opening provided in a pressure vessel, which does not require any compensation is 200 mm

What is the correct answer?

4

Which of the following is prone to cup and cone fracture?

A. Cast iron

B. Soft brass

C. Round specimen of ductile metal

D. Flat tensile specimen of ductile metal

What is the correct answer?

4

Pick out the wrong statement.

A. Ductile fracture of a stressed material, which exhibits a large plastic deformation is commonly caused by the formation and coalescence of voids in the necked region

B. Brittle fracture is caused by the propagation of pre-existing cracks in the material and involves minimum plastic deformation

C. Fatigue fracture of a material is always brittle in nature and takes place due to the existence of line imperfections

D. Brittle materials are generally tested in tension

What is the correct answer?

4

Hooke's law

A. Applies to elastic deformation

B. Applies beyond limit of proportionality in stress-strain curve

C. States that stress is inversely proportional to strain upto elastic limit

D. None of these

What is the correct answer?

4

Magnesium is present in

A. Haemoglobin

B. Chlorophyll

C. Hypo solution

D. None of these

What is the correct answer?

4

Enzymes belong to the category of

A. Proteins

B. Carbohydrates

C. Vitamins

D. Fats

What is the correct answer?

4

Good design of the casing of a centrifugal pump aims at minimising the

A. Cavitation

B. Frictional losses

C. Kinetic energy loss

D. Static head

What is the correct answer?

4

Triple point of water is

A. 0°F

B. 492°R

C. 0°K

D. -273°C

What is the correct answer?

4

Which of the following is not the commercial name of poly-methyl-methacrylate (PMMA)?

A. Styrofoam

B. Lucite

C. Perspex

D. Plexiglass

What is the correct answer?

4

Minimum temperature upto which water can be theoretically cooled down in the cooling tower by evaporative cooling is equal to the __________ temperature of air.

A. Wet bulb

B. Dry bulb

C. Saturation

D. Dew point

What is the correct answer?

4

Fibre glass is a composite material of

A. Glass fibre in a polymer matrix

B. Glass fibre in a metallic matrix

C. Polymer fibre in a glassy matrix

D. Both 'b' & 'c'