Isometric drawings are often used by ________ to help illustrate complex designs.
Mechanical engineers
Piping drafters
Aerospace engineers
All of the above
Correct Answer :
D. All of the above
Related Questions
These gears transmit power between shafts whose axes intersect at any angle:
Worm gears
Spur gears
Bevel gears
Racks
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
Circular
Elliptical
Lengthened
Angular
These are lines drawn on a map to locate, in the plan view, points of equal ground elevation:
Contours
Elevations
Profiles
Hatches
If a plane is parallel to the plane of projection, it appears:
True size
As a line or edge
Foreshortened
As an oblique surface
The Offset tool should only be used for placing ________ in an isometric drawing.
Circles
Horizontal lines
Vertical lines
None of the above
One critical issue drafters need to pay close attention to is the ________.
Size of the sheet
Designer's intent
Scale factor
None of the above
A drafter who develops technical drawings of a highway overpass would most likely be a ________ drafter.
Architectural
Civil
Mechanical
Process piping
In an assembly section, these parts should have their section lines left out or shown solid black:
Bolts
All fasteners
Thin parts
Rivets
In this type of section, one quarter of the object is removed:
Revolved section
Removed section
Quarter section
Half section
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
Dimension line
Extension line
Leader
Specification
This type of rapid prototyping system uses a laser to fuse powdered metals, plastics, or ceramics:
Fused deposition modeling
Stereo lithography apparatus
Solid ground curing
Selective laser sintering
The building construction industry relies on sets of ________ drawings to construct homes and commercial buildings.
Mechanical
Isometric
Architectural working
All of the above
These are used to attach parts to a cylinder so they won't turn on it:
Lugs and bearings
Key-seats and bearings
Knurls and keys
Keys and keyways/key-seats
This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
Boss
Spotface
Counterbore
Countersink
This is the plane upon which the top view is projected:
Horizontal
Frontal
Profile
Base
Some of the common terms used to describe technical drawing include:
Drafting
Engineering Graphics
Engineering Drawing
All of the above
The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section.
Full
Half
Quarter
None of the above
A partial auxiliary view is used to show only the ________ in the auxiliary view.
Projected inclined plane
The projected top view
The projected side view
None of the above
This type of structural steel drawing shows all dimensions necessary for fabrication:
Shop drawings
Design drawings
Weldment drawings
Application drawings
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
Primary
Secondary
Revolved
Partial
The Press-Pull tool will ________ the face of a solid model in the direction it faces.
Taper
Extrude
Spiral
None of the above
In the section view, the areas that would have been in actual contact with the cutting plane are shown with:
A cutting plane line
Section lining
Visible lines
Lines and arrows
In this type of concrete, the steel is pre-tensioned before the superimposed load is applied:
Aggregate
Pre-stressed
Reinforced
Preloaded
This type of section is limited by a break line:
Removed section
Revolved section
Broken-out section
Half section
In architectural drawing ________ are often used to illustrate and detail structural components.
Foundation beam detail sections
Wall sections
Building sections
All of the above
The maximum and minimum sizes of a feature are identified by a ________ tolerance.
Limits
GD&T
Reference
Allowance
When the receding lines are true length, and the projectors are at 45 degrees to the plane of projection, the oblique drawing is called this:
Cabinet projection
Cavalier projection
Axonometric projection
Isometric projection
Technical drawings typically serve one of three purposes:
Visualization, Communication, or Documentation
Visualization, Dimensioning, or Documentation
Communication, Documentation, or Installation
Documentation, Installation, or Engineering
This type of drawing is created to calculate areas, locate property lines, and locate building projects and facilities:
Traverse
Contour
City map
Plat
Geometric primitives include shapes such as ________.
Boxes
Cylinders
Wedges
All of the above