Related Questions
What is the correct answer?
4
To improve the machinability of steel, it is generally subjected to
What is the correct answer?
4
Strain hardening effect in metals subjected to cold working is due to the __________ mechanism.
What is the correct answer?
4
Production of a hollow product by inflation of a tube or parison is called the __________ process.
What is the correct answer?
4
Which of the following is not categorised as the ore agglomeration process?
What is the correct answer?
4
Which of the following is resistant to the action of both heat & chemicals?
What is the correct answer?
4
Alloys having more than 80% copper are generally more
C. Prone to season cracking
What is the correct answer?
4
Pick out the correct statement about the condensation.
A. Filmwise condensation gives a lower heat transfer rate than the dropwise condensation
B. Suitable coating or vapour additive is used to promote film wise condensation
C. If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it
D. Reynolds number of condensing liquid is based on its mass flow rate
What is the correct answer?
4
Internal energy of a gas obeying Van-Der- Waals equation of state, [p + (a/v2)] (V - b) = RT, depends upon its
A. Pressure & temperature
B. Pressure & specific volume
C. Temperature & specific volume
What is the correct answer?
4
The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
What is the correct answer?
4
Factor of safety is the ratio of the __________ stress to the working stress.
What is the correct answer?
4
Between 230 and 370°C, blue brittleness is caused in mild steel because of the
A. Immobility of dislocation
C. Increase in Young's modulus
What is the correct answer?
4
The minimum and the maximum number of members required to form a Private Limited Joint Stock Company are respectively
What is the correct answer?
4
The Al2O3 content of cryolite in Hall- Heroult cell is maintained between __________ percent.
What is the correct answer?
4
With increase in temperature, the electrical conductivity of a __________ decreases.
What is the correct answer?
4
Which of the following rays has the least wavelength?
What is the correct answer?
4
Which of the following is the largest quantum of pressure?
What is the correct answer?
4
Laser welding is widely employed in the __________ industries.
What is the correct answer?
4
Sand used to stop the green sand from sticking to the pattern is termed as the __________ sand.
What is the correct answer?
4
Which of the following contributes maximum as main source of sulphur in the blast furnace charge?
What is the correct answer?
4
Tempering of a material does not improve its
What is the correct answer?
4
Increasing sulphur content in pig iron tends to make it
What is the correct answer?
4
__________ rubber is generally used for making 'O' rings used for vacuum sealings.
What is the correct answer?
4
Which of the following does not have a sharp melting point?
What is the correct answer?
4
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by
What is the correct answer?
4
The product of a commercial direct reduction process is
D. Iron saturated with carbon
What is the correct answer?
4
Milk is fat dispersed in water. It is an example of
What is the correct answer?
4
A 2 kg object weighs 1.8 kgf on a spring balance. The value of 'g' at that location in m/sec2 is
What is the correct answer?
4
Which of the following is an ore dressing operation?
What is the correct answer?
4
The most important consideration, while designing the refrigeration system of an aircraft is that the refrigeration system
A. Is as light as possible
C. Employs minimum quantity of refrigerant
D. Consumer minimum horse power
What is the correct answer?
4
Which of the following is a commonly used manometric liquid for low pressure range?