Related Questions
What is the correct answer?
4
Corona discharge is related to the operation of a/an
B. Electrostatic precipitator
D. Magneto hydrodynamic generator (MHD)
What is the correct answer?
4
For the Stoke's law to be valid in the case of a falling sphere in a fluid, the
A. Reynolds number (based on sphere diameter) should be < 1
B. Flow around the sphere should be in turbulent region
C. Sphere must be metallic
D. Fluid density should be constant
What is the correct answer?
4
Identify the correct statement with reference to the extractive metallurgy of aluminium.
A. The electrolyte consists of molten Na3AlF6 with approximately 1 to 8% Al2O3
B. Approximately 80% of the aluminium deposited on the cathode comes from cryolite
C. Sodium is deposited along with aluminium, but is immediately vaporised
D. Anode effect sets in when the cryolite concentration goes below 40%.
What is the correct answer?
4
Maximum amount of thermal radiation is emitted at all wavelengths at any specified temperature by a/an __________ body.
What is the correct answer?
4
During sensible heating of humid air
A. Relative humidity increases
B. Dew point remains constant
C. Dry bulb & wet bulb temperature increases
What is the correct answer?
4
Babbitt lining is used on brass/bronze bearings to increase the
A. Antifriction properties
What is the correct answer?
4
Which of the following test is used for distinguishing among dry oils, semi-drying oils and non drying oils?
B. Reichert-Meissl value test
What is the correct answer?
4
If the head is doubled in & centrifugal pump, the power required will increase in the ratio of
What is the correct answer?
4
Sudden fall of atmospheric pressure by a large amount is an indication of the
What is the correct answer?
4
Which of the following is not categorised as the ore agglomeration process?
What is the correct answer?
4
The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the
D. Stress recovery effect
What is the correct answer?
4
Which of the following is not a characteristic observed in material failure by fatigue fracture?
A. Plastic deformation of material does not occur
B. Initiation of crack from below the surface does not occur
C. Initiation of crack occurs on the surface of the machine part
D. Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface
What is the correct answer?
4
Hot extrusion process is not used for making
A. Cast iron pipe for domestic water supply
B. Aluminium curtain rods
C. Stainless steel tubes used in furnitures
What is the correct answer?
4
Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter.
What is the correct answer?
4
Tip of the match stick contains a mixture of
What is the correct answer?
4
In an amorphous material, atoms defy any definite atomic structure and exist in random pattern just like in liquid. Which of the following is an amorphous material?
What is the correct answer?
4
Yield strength of a polycrystalline metal with an average grain size d, is proportional to
What is the correct answer?
4
Window panes of aeroplanes are normally made of
C. Bakelite (phenol formaldehyde)
What is the correct answer?
4
Electrical conductivities of semi-conductors are of the order of __________ ohm/cm.
What is the correct answer?
4
Which of the following emissions in the exhaust gas of an I.C. engine causes the formation of photochemical smog?
What is the correct answer?
4
About __________ ton of coke is required in a cupola to produce one ton of casting.
What is the correct answer?
4
Non-ferrous alloys used for making cutting tools need not have high
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the
What is the correct answer?
4
The heat of neutralisation remains constant, when there is a reaction between dilute solutions of strong
What is the correct answer?
4
An approximately __________ process exemplifies the flow of a gas through a very long pipe of uniform cross-section.
What is the correct answer?
4
Cold chisel & hammers are made of
What is the correct answer?
4
__________ joint is usually used for joining cast iron pipes mostly used for temporary pipelines, where it may be necessary to dismantle & reassemble the pipeline very frequently.
What is the correct answer?
4
Otto cycle used in spark ignition petrol engines is also known as the constant __________ cycle.
What is the correct answer?
4
Highest cutting speed is achieved by the __________ tool material.
What is the correct answer?
4
A solution which resists change in its pH value on addition of acid/alkali is called the __________ solution.