Related Questions
What is the correct answer?
4
Dislocation cross-slip is difficult in those materials, which have
A. Large number of slip systems
B. High work hardening rate
D. Low stacking fault energy
What is the correct answer?
4
The heat of neutralisation remains constant, when there is a reaction between dilute solutions of strong
What is the correct answer?
4
Fire refining process is employed in case of
What is the correct answer?
4
Which of the following materials does not form adherent oxide film on surface?
What is the correct answer?
4
Absolute zero, pressure will occur, when the molecular momentum of the system becomes zero. A liquid will cease to exist as liquid at
What is the correct answer?
4
Which one can be directly solidified from gaseous state without entering into liquid state?
What is the correct answer?
4
Mho's scale of hardness, which consists of 10 standard minerals is used for the measurement of __________ hardness.
What is the correct answer?
4
Notched bar test is used for testing the __________ of a material.
What is the correct answer?
4
Addition of small amount of __________ to grey cast iron is done to produce nodular grey cast iron.
What is the correct answer?
4
Screws are specified by their __________ diameters.
What is the correct answer?
4
The fugacity of liquid water at 298 K is approximately 3171 Pa. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be
What is the correct answer?
4
Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of
What is the correct answer?
4
The rolling process cannot be used to produce
What is the correct answer?
4
Which of the following hardness tests does not measure the indentation hardness of metals and alloys?
B. Shore scleroscope test
D. Rockwell hardness test
What is the correct answer?
4
Particle nature of cathode rays is proved due to the fact that they
A. Travel in a straight line
B. Get deflected by magnetic electric field
D. Heat the exposed material
What is the correct answer?
4
Which of the following is not an explosive?
What is the correct answer?
4
Which of the following is normally not found in both the S.I. (petrol) & C.I. (diesel) engines?
What is the correct answer?
4
Fibrous fracture is normally encountered in the __________ materials.
What is the correct answer?
4
Use of flux during soldering is done to
A. Increase fluidity of solder by lowering its melting temperature
B. Prevent oxide formation
C. Wash away surplus solder
What is the correct answer?
4
Recrystallisation temperature of steel is __________ °C.
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
For the Stoke's law to be valid in the case of a falling sphere in a fluid, the
A. Reynolds number (based on sphere diameter) should be < 1
B. Flow around the sphere should be in turbulent region
C. Sphere must be metallic
D. Fluid density should be constant
What is the correct answer?
4
Pick out the wrong statement
A. Processing of thermosetting plastics is ideally done by injection moulding
B. Processing of thermoplastics is ideally done by compression moulding
C. Mass production of seamless pipes are done by electrical resistance welding (ERW)
D. Stretch forming is a process of cold drawing
What is the correct answer?
4
The mechanism which changes the value of manipulated variable in response to the output signal from the control unit is called the
C. Floating control action
What is the correct answer?
4
In case of water (Prandtl number ≈ 6) flowing over a flat plate heated over the entire length, the thermal boundary layer thickness as compared to hydrodynamic boundary layer thickness is
What is the correct answer?
4
Pick out the wrong statement.
A. Cold cracking of a weld is due to the presence of hydrogen gas in the weld
B. True stress is given by, σ = σE (1 + εE), where σE and εE are engineering stress and engineering strain respectively
C. Phosphorous can be easily recovered in the iron blast furnace
D. High residual stress at the surface is beneficial for fatigue properties of a material
What is the correct answer?
4
If the head is doubled in & centrifugal pump, the power required will increase in the ratio of
What is the correct answer?
4
For separating small pieces of metal from engine oil of a car, the best separating technique is the
D. Fractional distillation
What is the correct answer?
4
Neutrons are present in all atoms except that of
What is the correct answer?
4
Broaching tools are usually made of