Related Questions
What is the correct answer?
4
Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
B. Type 3 back slash and enter
C. Type 3 forward slash and enter
D. Type 3 and try to use the Dynamic Input readout to find the end point
What is the correct answer?
4
This is a systematic approach that integrates the design and manufacture of products with the goal of optimizing the process:
A. Traditional engineering design
B. The manufacturing process
What is the correct answer?
4
A full scale technical drawing will have a scale factor of ________.
What is the correct answer?
4
Inserting blocks into a drawing file usually requires exacting placement. The drafter should insure that ________ is turned on.
What is the correct answer?
4
A line drawn with a long section, short dash, and another long section is a ________.
C. Center axis of a hidden cylinder
What is the correct answer?
4
This is a rounded exterior blend between surfaces:
What is the correct answer?
4
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
C. Block Definition Dialog
What is the correct answer?
4
The ________ is a standard element of a section view in a technical drawing.
C. Material hatch pattern
What is the correct answer?
4
These weld symbols have no arrow-side or other-side significance:
A. Projection or seam weld
C. Surface or groove weld
What is the correct answer?
4
This is the plane upon which the top view is projected:
What is the correct answer?
4
A half-moon protractor is divided into how many degrees?
What is the correct answer?
4
The dimension text size is determined by what the architect deems necessary in __________.
What is the correct answer?
4
In some circumstances an entire drawing can be inserted into a different drawing as a block. When this is used the base point will default to ________.
What is the correct answer?
4
Lines of an isometric drawing that are not parallel to the isometric axes are called this:
What is the correct answer?
4
This type of solid has a polygon for a base and triangular lateral faces that intersect at a vertex:
What is the correct answer?
4
The primary unit of measurement for engineering drawings and design in the mechanical industries is the:
What is the correct answer?
4
An advantage of this type of view is that each view shows the object all the way through as if it were transparent:
What is the correct answer?
4
These breaks are used to shorten the view of an object:
What is the correct answer?
4
Generally, the units used on an architectural drawing are set to ________.
What is the correct answer?
4
Students can complete an associate's degree in drafting which normally takes about ________ years to complete.
What is the correct answer?
4
This type of section is limited by a break line:
What is the correct answer?
4
On typical electronic diagrams, these items need not be shown unless they are needed for clarification:
What is the correct answer?
4
This type of solid is egg-shaped and can be created by revolving an ellipse around one of its axes:
What is the correct answer?
4
The Auto-CAD command used to combine two or more primitive shapes into a single complex 3-dimensional model is ________.
What is the correct answer?
4
This type of surface may be a plane, a single curved surface, or a warped surface:
What is the correct answer?
4
This type of thread is a thread on the inside of a member:
What is the correct answer?
4
The Offset tool should only be used for placing ________ in an isometric drawing.
What is the correct answer?
4
This is formed where three or more surfaces intersect:
What is the correct answer?
4
Given a situation in which the drafter has crossed extension lines in a drawing what can be done to clean up the point of crossing?
A. Use the Modify tool to clean up the extension lines
B. Use the Tolerance tool to clean up the extension lines
C. Use the Break tool to clean up the extension lines
D. Use the stretch tool to clean up the extension lines
What is the correct answer?
4
This type of section is not in direct projection from the view containing the cutting plane: