Related Questions
What is the correct answer?
4
Addition of __________ to steel does not help in improving its machinability.
What is the correct answer?
4
The atmospheric temperature during melting of ice/snow (in the atmosphere)
D. May increase or decrease; depends on the altitude where snow melts
What is the correct answer?
4
Dryness factor of steam is defined as the ratio of the mass of vapor in the mixture to the mass of the mixture. Dryness factor of steam is measured by a __________ calorimeter.
What is the correct answer?
4
The most suitable material for die casting is
What is the correct answer?
4
Wrought iron is never shaped by
What is the correct answer?
4
Recrystallisation temperature of steel is __________ °C.
What is the correct answer?
4
Which of the following is not used as a bearing material?
What is the correct answer?
4
In __________ process, there is an increase in entropy with no degradation of energy.
B. Isochoric heat addition
D. Isobaric heat addition
What is the correct answer?
4
__________ test determines the yield strength, Young's modulus of elasticity, percentage reduction in area & percentage elongation of a material.
What is the correct answer?
4
Water-tube boiler is the one, in which
A. Water passes through tubes and flue gases around it
B. Tube carrying hot flue gases are immersed in a pool of water
C. Tubes are placed in vertical position
What is the correct answer?
4
The boiling & freezing points on a newly defined temperature scale in degree 'D' are 400°D & 100°D respectively. The temperature reading corresponding to 60°C on this new temperature scale will be equal to __________ °D.
What is the correct answer?
4
Energy of the sun arises mainly from __________ reactions.
What is the correct answer?
4
Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.
What is the correct answer?
4
Consumable electrodes are used in the __________ welding.
What is the correct answer?
4
Which of the following emissions in the exhaust gas of an I.C. engine causes the formation of photochemical smog?
What is the correct answer?
4
Electrochemical corrosion can occur, only if __________ is present in contact with metal.
What is the correct answer?
4
Energy to be supplied to the radioactive nucleus for the emission of a neutron is __________ MeV.
What is the correct answer?
4
Quartz is a __________ material.
What is the correct answer?
4
Iron content in Indian iron ore is about __________ percent.
What is the correct answer?
4
Minimum thermal efficiency of a steam boiler may be around __________ percent
What is the correct answer?
4
Hot & cold working of material causes its __________ deformation.
What is the correct answer?
4
Cold working of a material results in increase in hardness, which is termed as the __________ hardening.
What is the correct answer?
4
X-rays are
D. Of higher wavelength than visible light
What is the correct answer?
4
The most important consideration, while designing the refrigeration system of an aircraft is that the refrigeration system
A. Is as light as possible
C. Employs minimum quantity of refrigerant
D. Consumer minimum horse power
What is the correct answer?
4
Which of the following phenomenon will exhibit the minimum heat transfer?
B. Forced convection in air
C. Free convection in air
What is the correct answer?
4
Function of gear box is to
What is the correct answer?
4
Hooke's law
A. Applies to elastic deformation
B. Applies beyond limit of proportionality in stress-strain curve
C. States that stress is inversely proportional to strain upto elastic limit
What is the correct answer?
4
Corrosion of metals cannot be prevented by its
What is the correct answer?
4
__________ fluid force is not considered in the Navier-Stokes equation.
What is the correct answer?
4
Good design of the casing of a centrifugal pump aims at minimising the