Related Questions
What is the correct answer?
4
Propulsion of rocket follows from the
A. Newton's second law of motion
B. Newton's third law of motion
What is the correct answer?
4
Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm.
What is the correct answer?
4
Superheating of steam is done at constant
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
At the point of boundary layer separation in fluid flow, the
A. Shear stress is maximum
B. Velocity gradient is flat
C. Density variation is maximum
What is the correct answer?
4
Internal energy of a gas obeying Van-Der- Waals equation of state, [p + (a/v2)] (V - b) = RT, depends upon its
A. Pressure & temperature
B. Pressure & specific volume
C. Temperature & specific volume
What is the correct answer?
4
In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are.
A. μ , α and θ all have units of m/s
B. μ , α and θ all have units of m2/s
C. α and θ have units of m2/s, while μ has unit of m/s
D. α and θ have units of m/s, while μ has unit of m2/s
What is the correct answer?
4
An abrupt and sudden fall in the reading of barometer is an indication of the
What is the correct answer?
4
Specific __________ is a dimensionless quantity.
What is the correct answer?
4
Breakeven point represents the condition, when the company runs under no profit no loss condition. In break even analysis, total cost comprises of fixed cost
What is the correct answer?
4
Percentage of argon (by volume) in dry atmospheric air is about
What is the correct answer?
4
Case hardening of a material is
A. Followed by tempering or carburising
B. Preceded by its tempering
C. Done to get a soft ductile interior with a very hard surface
D. Carried out to get extreme hardness in its core
What is the correct answer?
4
Hot extrusion of aluminium is done in the temperature range of __________ °C.
What is the correct answer?
4
Which of the following has the least value of ultimate tensile strength (UTS)?
What is the correct answer?
4
A material subjected __________ must have high resilience.
What is the correct answer?
4
Thermal conductivity of a material does not depend upon its
What is the correct answer?
4
Transformation range for ferrous material is the temperature interval during which __________ is formed during its heating.
What is the correct answer?
4
Recrystallisation temperature of steel is __________ °C.
What is the correct answer?
4
Cupola produces __________ iron.
What is the correct answer?
4
The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
What is the correct answer?
4
Which of the following fastening devices has a head at one end and a nut fitted to the other?
What is the correct answer?
4
The ratio of thermal & electrical conductivity is same for all the metals at the same temperature; and at around room temperature, this ratio is proportional to(where, T = absolute temperature, °K)
What is the correct answer?
4
Normalising of a casting does not
B. Refine its grain structure
D. Improve its mechanical properties
What is the correct answer?
4
In case of condensers & evaporators operating under given terminal conditions, LMTD (logarithmic mean temperature difference) for counter flow as compared to that for parallel flow is
What is the correct answer?
4
The refractory lining of the bottom in a basic electric arc furnace is made of
What is the correct answer?
4
Which one is neutral in character?
What is the correct answer?
4
Dislocations are __________ defects.
What is the correct answer?
4
Dowtherm is a
A. High temperature heating medium (a petroleum product)
B. Product of coal tar distillation
C. Very heat sensitive material
What is the correct answer?
4
A dummy activity is used in PERT network to describe the
A. Precedence relationship
What is the correct answer?
4
The product of a commercial direct reduction process is
D. Iron saturated with carbon