Related Questions
What is the correct answer?
4
__________ is the process of coating the surface of steel with aluminium oxide, thereby imparting it increased resistance to corrosion & oxidation upto a temperature of 700°C.
What is the correct answer?
4
Oxide layer formed on the non-ferrous metal surface after its annealing is
A. Removed by acid pickling
B. Hammered into the surface
C. Removed with coarse emery cloth
D. Left as such to protect the surface
What is the correct answer?
4
Which of the following alloying elements is present in maximum percentage in high speed steel?
What is the correct answer?
4
Shaft/rotor speed is most accurately measured by a
What is the correct answer?
4
Fibre reinforced plastic (FRP) are
A. Made of glass fibre and thermoplastic resins
C. Made of thermosetting resin and glass fibre
What is the correct answer?
4
In the acid Bessemer process, the hot metal should have the following composition.
A. S < 0.05% and P < 0.05%
B. S < 0.05% and P < 1.5%
C. S < 0.05% and P > 1.5%
D. S > 1.5% and P < 0.05%
What is the correct answer?
4
A material subjected __________ must have high resilience.
What is the correct answer?
4
Air standard Otto cycle is more efficient than the diesel cycle for the same
A. Heat addition & compression ratio
B. Heat addition & pressure
C. Compression ratio & pressure
D. Cylinder dimension & rpm
What is the correct answer?
4
Alloys having more than 80% copper are generally more
C. Prone to season cracking
What is the correct answer?
4
Hydro-cyclone is a
What is the correct answer?
4
Age hardening is connected with
What is the correct answer?
4
Which of the following metals reacts violently with water?
What is the correct answer?
4
Most important property of steels for use in automobile bodies is the
What is the correct answer?
4
Which of the following is used to produce draught in the locomotive boilers?
What is the correct answer?
4
One ton of refrigeration is not equivalent to the heat removal rate of
What is the correct answer?
4
Gantt charts are used for streamlining the
What is the correct answer?
4
If the demand for an item is trebled and the order cost is reduced to one third, then the economic order quantity
C. Decreases by a factor of 3
D. Decreases by a factor of 1/3
What is the correct answer?
4
When dry bulb temperature & wet bulb temperature of moist air is the same, it means that the
A. Partial pressure of water vapour is less than the total pressure
B. Humidity is < 100% & dew point temperature of air has not reached
C. Dew point temperature of air has not reached & air is not saturated fully
D. Air is fully saturated
What is the correct answer?
4
The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity.
What is the correct answer?
4
__________ circuit is most commonly used to measure strain with the help of a strain gauge.
B. Voltage balancing potentiometric
C. Simple current sensitive
What is the correct answer?
4
Which of the following forces does not act on a fluid at rest?
What is the correct answer?
4
The lightest non-inflammable gas is
What is the correct answer?
4
Wavelength of radiation emitted by a body depends on the __________ of its surface.
What is the correct answer?
4
Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen.
What is the correct answer?
4
The pressure outside a bubble/droplet of liquid is __________ the internal pressure.
D. Unpredictable; depends on the bubble size
What is the correct answer?
4
Yield strength of a material is determined by the __________ test.
What is the correct answer?
4
__________ is not a case hardening process.
What is the correct answer?
4
Tempering of a material does not improve its
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called
What is the correct answer?
4
__________ metal is used as a bearing liner material.