Normalising of an object does not

Question

Normalising of an object does not

A. Refine coarse grain structure obtained during hot working

B. Improve ductility

C. Improve yield strength

D. Improve mechanical properties

Share this question with your friends

Show all Chemical Engineering Basics MCQ

Comment

Nitriding of a steel part does not increase its

A. Grain size

B. Fatigue limit

C. Surface hardness

D. Wear resistance

Discuss this answer

Which of the following low melting alloy containing bismuth and lead is used for electric fuse?

A. Wood's metal

B. Babbitt metal

C. Monel metal

D. Duralumin

Discuss this answer

Which of the following does not discharge the dust collected as a dry solid?

A. Electrostatic precipitator

B. Wet scrubber

C. Bag filter

D. Gravity settling chamber

Discuss this answer

With increase in __________ Knocking tendency in a spark ignition petrol engine decreases.

A. Supercharging

B. Wall temperature

C. Compression ratio

D. Engine speed

Discuss this answer

Which of the following contributes maximum as main source of sulphur in the blast furnace charge?

A. Sinter

B. Coke

C. Iron ore

D. Limestone

Discuss this answer

Out of the following, the __________ pipe has the least corrosion resistance.

A. Mild steel

B. Copper

C. Cast iron

D. Wrought iron

Discuss this answer

The joint for soldering is supported by binding wire made of

A. Mild steel

B. Copper

C. Soft iron

D. Stainless steel

Discuss this answer

Highest cutting speed is achieved by the __________ tool material.

A. High speed steel

B. Carbide

C. Cast alloy

D. Plain carbon steel

Discuss this answer

The diffusion co-efficient of Ni in Cu at 1000 K is 1.93 × 10^-16 m²S^-1 and it is 1.94 × 10^-14 m²S^{- 1} at 1200 K. The activation energy (in k. J.mole-1) for the diffusion of Ni in Cu is

A. 130

B. 180

C. 230

D. 250

Discuss this answer

Hooke's law

A. Applies to elastic deformation

B. Applies beyond limit of proportionality in stress-strain curve

C. States that stress is inversely proportional to strain upto elastic limit

D. None of these

Discuss this answer

Secondary hardening in steels arises out of the

A. Precipitation of fine alloy carbides at high temperatures

B. Refinement of ferrite grain size by working

C. Decomposition of retained austenite upon heat treatment

D. Precipitation of complex inter-metallic upon heat treatment

Discuss this answer

__________ pipe is the most suitable for carrying sanitary drainage.

A. Stainless steel

B. Reinforced cement concrete

C. Cast iron

D. Asbestos cement

Discuss this answer

For separating small pieces of metal from engine oil of a car, the best separating technique is the

A. Chromatography

B. Evaporation

C. Filtration

D. Fractional distillation

Discuss this answer

An example of unsteady non uniform flow is the flow of liquid under pressure through a

A. Tapering pipe at constant flow rate

B. Tapering pipe at either decreasing or increasing flow rate

C. Long pipeline of constant diameter

D. None of these

Discuss this answer

Potable water means the water used for

A. Fire-fighting

B. Cooling

C. Drinking

D. Evaporation to produce steam

Discuss this answer

Increase in the entropy of a system represents the

A. Degradation of energy

B. Decrease in system pressure

C. Increase in the availability of energy

D. Increase in the temperature

Discuss this answer

Use of flux during soldering is done to

A. Increase fluidity of solder by lowering its melting temperature

B. Prevent oxide formation

C. Wash away surplus solder

D. Full up the joint gap

Discuss this answer

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m². °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.

A. 2

B. 8

C. 10

D. 40

Discuss this answer

Shampoos are commercially not available in the form of

A. Powder

B. Gaseous mixture

C. Solution

D. Emulsion

Discuss this answer

'Cryogenics' is concerned with the generation & use of low temperature in the range of

A. 0°K to 123°K

B. 0°C to - 123°C

C. 0°C to - 273°C

D. 0°K to 273°K

Discuss this answer

Which of the following fastening devices has its both ends threaded?

A. Bolt

B. Stud

C. Set screw

D. Split nut

Discuss this answer

Lead is poured into the joint between two __________ pipes.

A. Mild steel

B. Concrete

C. Cast iron

D. Asbestos cement

Discuss this answer

Blow off cock is provided in steam boiler to

A. Guard the boiler in case of abnormal rise in steam pressure

B. Drain out water and sludge during its repair

C. Regulate the supply of water in boiler

D. Put out the fire in the furnace when the water level in the boiler falls to unsafe limit

Discuss this answer

Tin based white metals are used, where bearings are subjected to

A. High pressure & load

B. Low pressure & load

C. High temperature

D. Large surface wear

Discuss this answer

Heat release during phase change is observed in case of a/an

A. Boiler

B. Condenser

C. Evaporator

D. All (A), (B) & (C)

Discuss this answer

Basic open hearth furnace (BOF) is not used for producing __________ steel.

A. Killed

B. Rimming

C. High alloy

D. None of these

Discuss this answer

Cemented carbide tools are not suitable for cutting

A. Aluminium

B. Brass

C. Cast iron

D. Steel

Discuss this answer

Which of the following is a commonly used manometric liquid for low pressure range?

A. Ethyl alcohol

B. Carbon tetrachloride

C. Glycerol

D. Ethylene glycol

Discuss this answer

Load cells used for the measurement of weight has

A. Compact & rugged construction with an accuracy of 0.1 to 1%

B. No moving parts and incurs negligible deflection under load

C. Provision of thermal compensation and is hermetically sealed

D. All 'a', 'b' & 'c'

Discuss this answer

Larger length & diameter water pipes are made by

A. Electrical resistance welding

B. Die casting

C. Semi-centrifugal casting

D. Continuous casting

Discuss this answer

Accepted Answer

B. Improve ductility

Normalising of an object does not

Correct Answer :

Show all Chemical Engineering Basics MCQ

Related Questions

Nitriding of a steel part does not increase its

Which of the following low melting alloy containing bismuth and lead is used for electric fuse?

Which of the following does not discharge the dust collected as a dry solid?

With increase in __________ Knocking tendency in a spark ignition petrol engine decreases.

Which of the following contributes maximum as main source of sulphur in the blast furnace charge?

Out of the following, the __________ pipe has the least corrosion resistance.

The joint for soldering is supported by binding wire made of

Highest cutting speed is achieved by the __________ tool material.

The diffusion co-efficient of Ni in Cu at 1000 K is 1.93 × 10^-16 m²S^-1 and it is 1.94 × 10^-14 m²S^{- 1} at 1200 K. The activation energy (in k. J.mole-1) for the diffusion of Ni in Cu is

Hooke's law

Secondary hardening in steels arises out of the

__________ pipe is the most suitable for carrying sanitary drainage.

For separating small pieces of metal from engine oil of a car, the best separating technique is the

An example of unsteady non uniform flow is the flow of liquid under pressure through a

Potable water means the water used for

Increase in the entropy of a system represents the

Use of flux during soldering is done to

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m². °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.

Shampoos are commercially not available in the form of

'Cryogenics' is concerned with the generation & use of low temperature in the range of

Which of the following fastening devices has its both ends threaded?

Lead is poured into the joint between two __________ pipes.

Blow off cock is provided in steam boiler to

Tin based white metals are used, where bearings are subjected to

Heat release during phase change is observed in case of a/an

Basic open hearth furnace (BOF) is not used for producing __________ steel.

Cemented carbide tools are not suitable for cutting

Which of the following is a commonly used manometric liquid for low pressure range?

Load cells used for the measurement of weight has

Larger length & diameter water pipes are made by

Also checkout

Normalising of an object does not

Correct Answer :

Show all Chemical Engineering Basics MCQ

Related Questions

Nitriding of a steel part does not increase its

Which of the following low melting alloy containing bismuth and lead is used for electric fuse?

Which of the following does not discharge the dust collected as a dry solid?

With increase in __________ Knocking tendency in a spark ignition petrol engine decreases.

Which of the following contributes maximum as main source of sulphur in the blast furnace charge?

Out of the following, the __________ pipe has the least corrosion resistance.

The joint for soldering is supported by binding wire made of

Highest cutting speed is achieved by the __________ tool material.

The diffusion co-efficient of Ni in Cu at 1000 K is 1.93 × 10-16 m2S-1 and it is 1.94 × 10-14 m2S- 1 at 1200 K. The activation energy (in k. J.mole-1) for the diffusion of Ni in Cu is

Hooke's law

Secondary hardening in steels arises out of the

__________ pipe is the most suitable for carrying sanitary drainage.

For separating small pieces of metal from engine oil of a car, the best separating technique is the

An example of unsteady non uniform flow is the flow of liquid under pressure through a

Potable water means the water used for

Increase in the entropy of a system represents the

Use of flux during soldering is done to

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.

Shampoos are commercially not available in the form of

'Cryogenics' is concerned with the generation & use of low temperature in the range of

Which of the following fastening devices has its both ends threaded?

Lead is poured into the joint between two __________ pipes.

Blow off cock is provided in steam boiler to

Tin based white metals are used, where bearings are subjected to

Heat release during phase change is observed in case of a/an

Basic open hearth furnace (BOF) is not used for producing __________ steel.

Cemented carbide tools are not suitable for cutting

Which of the following is a commonly used manometric liquid for low pressure range?

Load cells used for the measurement of weight has

Larger length & diameter water pipes are made by

Also checkout

The diffusion co-efficient of Ni in Cu at 1000 K is 1.93 × 10^-16 m²S^-1 and it is 1.94 × 10^-14 m²S^{- 1} at 1200 K. The activation energy (in k. J.mole-1) for the diffusion of Ni in Cu is

What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m². °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively.