Home
Current Affairs January 2024

What is the correct answer?

4

Nuclear fission of one atom of uranium-235 produces the energy equivalent to about __________ MeV.

A. 20

B. 200

C. 500

D. 2000

Correct Answer :

B. 200


Related Questions

What is the correct answer?

4

Electrometallurgy is not involved in the extraction of __________ from its ore.

A. Aluminium

B. Tin

C. Lead

D. Both (B) & (C)

What is the correct answer?

4

One of the methods of purification of leach liquor is ion exchange, which involves

A. Exchange between two liquid phases

B. Exchange between a gaseous phase and a liquid phase

C. Exchange between a liquid phase and an organic resin phase

D. Exchange between a solid phase and a gas phase

What is the correct answer?

4

When dry bulb temperature & wet bulb temperature of moist air is the same, it means that the

A. Partial pressure of water vapour is less than the total pressure

B. Humidity is < 100% & dew point temperature of air has not reached

C. Dew point temperature of air has not reached & air is not saturated fully

D. Air is fully saturated

What is the correct answer?

4

Which of the following is not a dielectric material?

A. Cotton, silk and paper

B. Asbestos, glass, porcelain and mica

C. Rubber and polymeric resins

D. All refractory materials

What is the correct answer?

4

Which of the following heat treatment processes is usually applied to castings?

A. Tempering

B. Annealing

C. Normalising

D. Carburising

What is the correct answer?

4

Natural water contains approximately __________ percent of heavy water.

A. 0.015

B. 0.71

C. 1.2

D. 3.5

What is the correct answer?

4

Metalloids

A. Are good conductor of heat & electricity

B. Act as electron donors with metals & as electron acceptor with non-metals

C. Are not necessarily solids at room temperature

D. Are compounds that exhibit both metallic & non-metallic properties to some extent and are exemplified by elements like germanium, silicon & boron

What is the correct answer?

4

The elastic strain in copper is due to the

A. Motion of dislocations

B. Stretching of atomic bonds

C. Breakage of atomic bonds

D. None of the above

What is the correct answer?

4

Air/fuel ratio on molar (volume) basis for combustion of methane with theoretical quantity of air with be

A. 9.5 : 1

B. 12.5 : 1

C. 15.5 : 1

D. 18.5 : 1

What is the correct answer?

4

at 1173E; at equilibrium, what will be the number of moles of CO gas required to reduce one mole of at 1173 K?

A. 1.0

B. 1.3

C. 2.3

D. 3.3

What is the correct answer?

4

Corrosion rate cannot be lowered by reducing the __________ of the corroding medium.

A. Concentration

B. Velocity

C. Temperature

D. None of these

What is the correct answer?

4

__________ cannot increase the fatigue strength of a material.

A. Grain refining

B. Grain coarsening

C. Surface hardening

D. Shot peening

What is the correct answer?

4

Boiling point of water gets lowered at high altitudes (e.g., hills), because

A. Temperature is low

B. Atmospheric pressure is low

C. Atmospheric pressure is high

D. None of these

What is the correct answer?

4

Which of the following commonly used condenser tube materials has the lowest thermal conductivity?

A. Admiralty brass

B. Stainless steel

C. Aluminium brass

D. Titanium

What is the correct answer?

4

Pick out the wrong statement

A. Processing of thermosetting plastics is ideally done by injection moulding

B. Processing of thermoplastics is ideally done by compression moulding

C. Mass production of seamless pipes are done by electrical resistance welding (ERW)

D. Stretch forming is a process of cold drawing

What is the correct answer?

4

Cast iron contains __________ percent carbon.

A. 2.5

B. 3.75

C. 4.75

D. 5.25

What is the correct answer?

4

__________ of grey cast iron produces white cast iron.

A. Tempering

B. Rapid heating

C. Rapid cooling

D. Slow cooling

What is the correct answer?

4

Difference at any instant between the value of the controlled variable and the set point is called the

A. Deviation

B. Derivative time

C. Error ratio

D. Differential gap

What is the correct answer?

4

Sacrificial anode method is used in the protection of pipelines which are buried underground. Sacrificial anode

A. Occurs higher in the electro-chemical series of metals

B. Is exemplified by magnesium plate

C. Is much cheaper than the cathodic base material to be guarded against corrosion

D. All (A), (B) & (C)

What is the correct answer?

4

Which of the following is a boiler accessory
i.e., not a boiler mounting?

A. Blow off cock

B. Feed check valve

C. Feed water pump

D. Stop valve

What is the correct answer?

4

Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.

A. 5-10

B. 1000-1500

C. 120-500

D. 1500-3000

What is the correct answer?

4

Vernier calipers cannot be used to measure the

A. I.D. & O.D. of the shaft

B. Thickness of parts

C. Depth of holes

D. Clearance between two mating surfaces

What is the correct answer?

4

Shrinkage allowance on pattern is provided to compensate for shrinkage when the

A. Metal changes from liquid state to solid state at freezing temperature

B. Solid phase temperature drops from freezing temperature to the room temperature

C. Liquid metal temperature drops from pouring temperature to room temperature

D. Liquid metal temperature drops from pouring temperature to freezing temperature

What is the correct answer?

4

In a drilling process, the metal is removed by both shearing & extrusion. General purpose drills are made of

A. Stainless steel

B. Mild steel

C. High speed steel

D. High carbon steel

What is the correct answer?

4

In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will

A. Decrease gradually

B. Increase gradually

C. Increase rapidly

D. Remain constant

What is the correct answer?

4

Function of fusible plug in a boiler is to

A. Drain out water and sludge from the boiler during repair

B. Put off fire in the furnace when water level in the boiler falls to unsafe limit

C. Guard the boiler in case of abnormal rise in steam pressure

D. All (A), (B) & (C)

What is the correct answer?

4

A cylindrical rod subjected to a tensile strain within the elastic limit undergoes a volume change. If the volume strain is equal to half the tensile strain, then the Poisson's ratio of the rod is

A. 0

B. 0.33

C. 0.44

D. 0.25

What is the correct answer?

4

Age hardening is connected with

A. Babbitt metal

B. Gun metal

C. Stainless steel

D. Duralumin

What is the correct answer?

4

Brass parts with high residual tensile stress at the surface are susceptible to season cracking (i.e. spontaneous cracking occuring on exposure to atmospheric corrosion), if its zinc percentage is more than

A. 5

B. 10

C. 20

D. 35

What is the correct answer?

4

The usual energy consumption in electric arc furnace steel making is __________ KWh/ton of steel.

A. 60 - 100

B. 400 - 700

C. 1200 -1500

D. 2000 - 2300