Related Questions
What is the correct answer?
4
Factor of safety in machine design is defined as the ratio of ultimate stress to __________ stress.
What is the correct answer?
4
Corrosion rate cannot be lowered by reducing the __________ of the corroding medium.
What is the correct answer?
4
__________ joint is usually used for joining cast iron pipes mostly used for temporary pipelines, where it may be necessary to dismantle & reassemble the pipeline very frequently.
What is the correct answer?
4
Materials having __________ lattice structure are usually the most ductile.
A. Body centred cubic (bcc)
B. Hexagonal close packed (hcp)
C. Face centred cubic (fcc)
What is the correct answer?
4
The elastic strain in copper is due to the
A. Motion of dislocations
B. Stretching of atomic bonds
C. Breakage of atomic bonds
What is the correct answer?
4
Plastics as a material of construction suffer from the drawback of low
What is the correct answer?
4
Triple point of water is
What is the correct answer?
4
Latent heat of dry steam at atmospheric pressure is 539 Kcal/kg; which __________ with increase in the pressure of steam.
D. May increase or decrease
What is the correct answer?
4
Cold heading or upsetting is categorised as the __________ process.
What is the correct answer?
4
Spheroidising of a material is a/an __________ process.
What is the correct answer?
4
Highest cutting speed is achieved by the __________ tool material.
What is the correct answer?
4
Austempering of steel requires it to be heated to 875°C followed by sudden cooling to 250-525°C, thereby changing austenite to
What is the correct answer?
4
Gross national product (GNP) means the total value of __________ in a country.
C. Earning of the citizens
What is the correct answer?
4
The delivery pressure of boiler feed water pump compared to the boiler steam pressure is
What is the correct answer?
4
Which one is neutral in character?
What is the correct answer?
4
__________ property of a material is determined by the Herbert Pendulum device.
What is the correct answer?
4
The ratio of the shear stress to the principal stress on a principal plane is
What is the correct answer?
4
'Dikes' are low height walls made around the storage vessels meant for storing hazardous & inflammable material (e.g., petroleum products). Volume of dikes is equal to (where, V = volume of the storage vessel)
What is the correct answer?
4
The 'laughing gas' is
What is the correct answer?
4
__________ cannot increase the fatigue strength of a material.
What is the correct answer?
4
Lead is poured into the joint between two- __________ pipes.
What is the correct answer?
4
__________ is not used as the control rod material in a nuclear reactor.
What is the correct answer?
4
In the blast furnace, incorporation of water vapour in the blast gives the following effect.
A. Increases the reducing potential of the gas
B. Increases the flame temperature
C. No significant change occurs
D. Increases the hydrogen content in the metal
What is the correct answer?
4
__________ is the trade name assigned to a nonferrous cast alloy composed of cobalt, chromium & tungsten.
What is the correct answer?
4
Thermal efficiency of an internal combustion engine is around __________ percent.
What is the correct answer?
4
In electrical resistance welding, distortion results from the use of improper
What is the correct answer?
4
Case hardening of a material is
A. Followed by tempering or carburising
B. Preceded by its tempering
C. Done to get a soft ductile interior with a very hard surface
D. Carried out to get extreme hardness in its core
What is the correct answer?
4
The ratio of mass of a neutron to that of an electron is about 1839. What is the ratio of the mass of a proton to that of an electron?
What is the correct answer?
4
Eutectoid composition of carbon steel at room temperature is
What is the correct answer?
4
The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge)