Objects that are symmetric can be shown effectively using this type of section:
Quarter section
Half section
Full section
Symmetric section
Correct Answer :
B. Half section
Related Questions
This type of solid is egg-shaped and can be created by revolving an ellipse around one of its axes:
Ellipsoid
Torus
Cone
Cylinder
Isometric drawings are often used by ________ to help illustrate complex designs.
Mechanical engineers
Piping drafters
Aerospace engineers
All of the above
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
Pull the line from away from the starting point very carefully
Insure that Ortho is on
Enter 3 for the length of the line
Read the coordinate position on the Dynamic Readout
In perspective drawings this is placed between the observer and the object:
Vanishing point / horizon
Station point
Ground line
Plane of projection / picture plane
These drawings are given to contractors to perform work or manufacture individual parts:
Assembly details
3D drawings
Working drawings
Skeleton assemblies
The Press-Pull tool will ________ the face of a solid model in the direction it faces.
Taper
Extrude
Spiral
None of the above
Acceptable parts must not extend beyond this:
Boundary limits
Hole limits
Specification
Tolerances
This type of circuit is a semiconductor wafer or chip:
Integrated circuit
Transmission circuit
Plotted circuit
Conducted circuit
Dimensions are used on the elevation plan to describe ________.
Finished floor elevations
Roof overhangs
Roof pitch angles
All of the above
The first step in creating a traditional technical drawing is to ________.
Draw a series of guide lines
Set up the meter line
Align the paper so that it will be positioned square to the parallel bar
Sharpen the leads in the technical pens
The ________ tool on the Dimension tool bar places the length of an arch on a drawing.
Arc Radius
Arc Length
Radius
Diameter
One way to evenly space dimensions on a drawing is to use the ________.
Dimension Space tool
Linear tool
Continue tool
Baseline tool
The typical parts list should include the ________.
Part number
Manufacturing material
Number of parts needed
All of the above
Using this as a communication and design review tool can help shorten the process and eliminate productivity barriers:
Development plans
Portable document files
The Internet and e-mail
Gantt charts
There are two main types of projection:
Parallel and Orthographic
Station-point and Perspective
Parallel and Convergent
Perspective and Parallel
These weld symbols have no arrow-side or other-side significance:
Projection or seam weld
Back or backing weld
Surface or groove weld
Flash and upset weld
The site plan illustrates ________.
The floor plan
Where the house sits on the property
The roof plan
Where the garage and driveway are located
This is a thin solid line directing attention to a note or dimension and starting with an arrowhead or dot:
Dimension line
Extension line
Leader
Specification
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
Primary
Secondary
Revolved
Partial
A back or backing weld is a type of:
Groove weld
Resistance weld
Arc and gas weld
Upset weld
This is a systematic approach that integrates the design and manufacture of products with the goal of optimizing the process:
Traditional engineering design
The manufacturing process
Concurrent design
Design for recycling
Architectural dimensioning is usually done in ________.
Even numbers
Feet and inches
Feet only
Inches only
The maximum and minimum sizes of a feature are identified by a ________ tolerance.
Limits
GD&T
Reference
Allowance
In an assembly section, these parts should have their section lines left out or shown solid black:
Bolts
All fasteners
Thin parts
Rivets
The title block used on working drawings should include the __________.
Sheet number
Line type
Layer set
All of the above
How can the drafter prevent Auto-CAD from placing or stacking another center mark on a circle when adding a diameter dimension to it?
Explode the dimension and then erase the center mark
Use the Properties dialog box to turn off the center mark of the dimension
It can't be done
Use the trim tool to take away the stacked center mark
A secondary auxiliary view is a projection off of the ________.
Front view
Top view
Primary auxiliary view
None of the above
Oblique sections are useful to show this:
Foreshortened features
Oblique lines
Interior shapes
Projected features
Placement of dimensions on a drawing is controlled by ________.
ANSI
The design engineer
Corporate drafting standards
All of the above
The ________ is a standard element of a section view in a technical drawing.
Cutting Plane line
Section lines
Material hatch pattern
All of the above