Related Questions
What is the correct answer?
4
Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
B. Type 3 back slash and enter
C. Type 3 forward slash and enter
D. Type 3 and try to use the Dynamic Input readout to find the end point
What is the correct answer?
4
In some circumstances an entire drawing can be inserted into a different drawing as a block. When this is used the base point will default to ________.
What is the correct answer?
4
The typical parts list should include the ________.
B. Manufacturing material
C. Number of parts needed
What is the correct answer?
4
Schematic and single-line diagrams should be arranged so that signal or transmission path from input to output proceeds in this fashion:
A. Right to left and top to bottom
B. Right to left and bottom to top
C. Left to right and top to bottom
D. Left to right and bottom to top
What is the correct answer?
4
These maps are used to plan construction projects that locate construction features so they fit the topography of the area:
C. Structural topography maps
D. Structure location plans
What is the correct answer?
4
Isometric drawings are often used by ________ to help illustrate complex designs.
What is the correct answer?
4
Angles project true size only when the plane containing the angle and plane of projection are this:
What is the correct answer?
4
Several of the tools used in traditional drafting include the following:
A. Parallel straight edge
What is the correct answer?
4
5.These items typically are not used in new designs, but are still common in high-power amplifiers:
What is the correct answer?
4
Traditional drafters need to be able to create several different line widths because ________.
A. Different line widths convey different information
B. The line width has to do with how dark it appear in the finished drawing
C. They seem to transmit better in a fax machine
D. It makes no difference
What is the correct answer?
4
In oblique projection, important shapes should be in this position relative to the viewing plane:
What is the correct answer?
4
Before starting an isometric drawing in Auto-CAD the drafter needs to ________.
A. Set the grid to isometric
B. Set the current layer to Defpoints
What is the correct answer?
4
This type of drawing shows two lines representing the pipe diameter:
What is the correct answer?
4
This type of thread is a thread on the inside of a member:
What is the correct answer?
4
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
What is the correct answer?
4
Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:
What is the correct answer?
4
When adding dimensions to an auxiliary view it will be necessary to use the ________ tool.
What is the correct answer?
4
This type of axonometric drawing has equal foreshortening along two axis directions and a different amount on the third axis:
What is the correct answer?
4
The most common geometric form used in gears today is this:
What is the correct answer?
4
The condition of a part when it contains the least amount of material is referred to as ________.
What is the correct answer?
4
These weld symbols have no arrow-side or other-side significance:
A. Projection or seam weld
C. Surface or groove weld
What is the correct answer?
4
This is the plane upon which the top view is projected:
What is the correct answer?
4
A civil engineer working on a bridge design would probably rely on his ________ scale for checking printed drawings.
What is the correct answer?
4
This is a systematic approach that integrates the design and manufacture of products with the goal of optimizing the process:
A. Traditional engineering design
B. The manufacturing process
What is the correct answer?
4
This type of section is not in direct projection from the view containing the cutting plane:
What is the correct answer?
4
In an assembly section, these parts should have their section lines left out or shown solid black:
What is the correct answer?
4
In this type of section, one quarter of the object is removed:
What is the correct answer?
4
Understanding the Cartesian coordinate system will help the beginning drafter ________.
A. Control the accuracy of the drawing
B. Produce a visible grid system
C. Select a different text style
D. Choose various line types
What is the correct answer?
4
This type of rapid prototyping system uses a laser to fuse powdered metals, plastics, or ceramics:
A. Fused deposition modeling
B. Stereo lithography apparatus
D. Selective laser sintering
What is the correct answer?
4
The Offset tool should only be used for placing ________ in an isometric drawing.