Related Questions
What is the correct answer?
4
Use of flux during soldering is done to
A. Increase fluidity of solder by lowering its melting temperature
B. Prevent oxide formation
C. Wash away surplus solder
What is the correct answer?
4
Matte smelting is used in the extraction of
What is the correct answer?
4
All the atoms of the world comprise of electrons, proton & neutron except that of __________ atom in which neutron is absent.
What is the correct answer?
4
Highest cutting speed is achieved by the __________ tool material.
What is the correct answer?
4
Fatigue limit improvement by over stressing the metal by successively increasing the load is called coaxing. In fatigue failure, the material fails
C. Below the elastic limit
What is the correct answer?
4
Pick out the correct statement
A. Jet engine can work, where there is no atmosphere
B. Rocket engines cannot work, where there is no atmosphere
C. Rocket engines carry oxygen required for the combustion in the form of oxidiser
D. Jet engines also carry oxidiser
What is the correct answer?
4
Tesla metre per ampere (T. m/A) is the unit for the measurement of
A. Magnetic susceptibility
C. Permeability of free space
What is the correct answer?
4
Carbon is present in the form of __________ in grey cast iron.
B. Nodular aggregates of graphite
What is the correct answer?
4
Desalination of water
C. Means distillation of water
What is the correct answer?
4
'Dikes' are low height walls made around the storage vessels meant for storing hazardous & inflammable material (e.g., petroleum products). Volume of dikes is equal to (where, V = volume of the storage vessel)
What is the correct answer?
4
Circular cross section machine parts which are symmetrical about the axis of rotation are made by hot
What is the correct answer?
4
Cementite is in the lamellar form in the __________ phase of steel.
What is the correct answer?
4
Gratings is associated with the measurement of
What is the correct answer?
4
What is the value of included angle of a triangular notch for maximum discharge?
What is the correct answer?
4
Angular displacement can be measured suitably by a
B. Linear variable differential transducer (LVDT)
What is the correct answer?
4
Which of the following is not a ferromagnetic material?
What is the correct answer?
4
Cold heading or upsetting is categorised as the __________ process.
What is the correct answer?
4
As the fluid flow rate increases, the float of the Rotameter
B. Rotates at higher speed
C. Rotates at lower speed
D. Drops down in the tube
What is the correct answer?
4
The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it.
What is the correct answer?
4
In the diving apparatus, helium is used along with oxygen, because it is
B. Not soluble in blood at high pressure
D. Completely miscible with oxygen
What is the correct answer?
4
In a totally irreversible isothermal expansion process for an ideal gas, ΔE = 0, ΔH = 0. Then ΔQ and ΔS will be
What is the correct answer?
4
Metal cutting by oxy-acetylene flame is accomplished by the __________ of the metal.
What is the correct answer?
4
Compressed dry air is used as the cutting fluid, while machining
What is the correct answer?
4
The refractory lining of the bottom in a basic electric arc furnace is made of
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
Venturimeter is used to measure the flow rate of fluids in pipes, when the pipe is in __________ position.
What is the correct answer?
4
For a first order chemical reaction, the concentration of the reactant decreases __________ with time.
What is the correct answer?
4
Fire refining process is employed in case of
What is the correct answer?
4
Alcohols are not suitable as diesel engine fuel because the cetane number of alcohols is
A. Very low which prevents their ignition by compression
B. Very high which prevents their ignition by compression
What is the correct answer?
4
Theoretical volume of oxygen required for complete combustion of 1Nm3 of acetylene, in oxyacetylene welding is __________ Nm3.