On the 1900 switch, how do you enter User EXEC mode?
It comes up by default.
Enter the letter U in the menu.
Enter the letter K in the menu.
Enter the letter C in the menu.
Correct Answer :
C. Enter the letter K in the menu.
Related Questions
Which of the following is a disadvantage of SANs?
Distance limitation
Cost
Overhead
Management
When examining the IP routing table, an EIGRP route will be shown as what letter?
I
E
O
D
Which of the following is true concerning 802.1Q?
It supports hub connections.
It is supported on both the 1900 and 2950 switches.
The native VLAN is tagged.
The original Ethernet frame is not modified.
There are _________ actions a router can take when there is a match on an ACL statement
1
2
3
4
You are given the following addressing information: 192.168.37.192/25. What type of address is this?
Network
Directed Broadcast
Host
If you enter a command in either User EXEC mode or Privilege EXEC mode that the IOS does not recognize, the switch or router
Logs you out
Tries to resolve the command to an IP address
Executes the closest command that it can find in its command set
Makes a "beep" sound
IOS images can be loaded from all the following except:
ROM
Flash
NVRAM
TFTP
The 1900 switch supports ________ VLANs.
10
32
64
250
If you see a VC with an inactive status, this indicates ____________.
The connection between both Frame Relay DTEs is up and operational.
The connection between your Frame Relay DTE and DCE is up and operational, but there is something wrong with connection between your connected Frame Relay switch and the destination DTE.
You are not receiving any LMI messages from the Frame Relay switch.
__________ states that if a neighboring router sends a route to a router, the receiving router will not propagate this route back to the advertising router on the same interface.
Split horizon
Poison reverse
Hold-down timer
Hop count limit
Which IGRP command allows unequal-cost load balancing?
variance
load
balance
network
Which command defines interesting traffic?
dialer-group
dialer-list
dialer map
dialer remote-name
When configuring a router-on-a-stick, the configuration is done on __________.
Physical interfaces
Major subinterfaces
Subinterfaces
You are given the following addressing information: 10.0.8.0/22. What type of address is this?
Network
Directed Broadcast
Host
Which of the following situations are best for DDR connections?
Primary WAN connection
A lot of constant traffic
Long phone calls
Backup connection
A _________ looks at OSI Reference Model layers 4-7 to make intelligent decisions about how to obtain information for a user.
SAN
LAN
CN
SAN and CN
When backing up your IOS image from flash, which of the following will the copy flash tftp command prompt you for? (Choose all correct answers.)
TFTP server IP address
Verification to copy
Source filename
Destination filename
Your router is running RIP and OSPF and both routing protocols are learning 192.168.1.0/24. Which routing protocol will your router use for this route?
RIP
OSPF
___________ has both physical and logical ring topologies.
Ethernet
FDDI
Token Ring
Which of the following is not true concerning TCP?
Provides for reliable connections
Uses windowing for flow control
Multiplexes applications
Is more efficient than UDP
What command creates a DHCP address pool on a router?
ip dhcp
ip pool dhcp
ip dhcp pool network
ip dhcp pool
The dialer map command contains all of the following parameters except __________.
Protocol name
Remote router name
Address of local router
Speed of the connection
A ___________ is basically all of the components, hardware and software, involved
in connecting computers across small and large distances.
LAN
WAN
Network
SAN
Which controller command specifies how ones and zeros are represented on a digital circuit?
framing
linecode
clock source
interface
The ___________ converts an ISDN four-wire connection to a two-wire connection.
NT5
NP1
NT1
TN1
Which 2950 command enables trunking?
switchport mode trunk
trunking on
trunking enable
switchport trunk on
Which command activates an IP ACL on a router's interface?
access-list
ip access-group
access-class
access-group
RIP has a hold-down period of ____________ seconds.
60
120
180
280
You are at User EXEC mode and type the letter e. What message appears?
% Incomplete command.
% Ambiguous command:
% Unknown command or computer name
% Invalid input detected at '^'.
A VTP server switch generates a summary advertisement every _________ minutes.
1
2
3
5