Once a drawing is determined to be complete, the title block is used to document the change from:
A draft to a finished drawing
A finished to a working drawing
An assembly to a finished drawing
A working drawing to a draft
Correct Answer :
A. A draft to a finished drawing
Related Questions
In this type of auxiliary view, a break line is used to indicate the imaginary break in the views:
Primary
Secondary
Revolved
Partial
An advantage of this type of view is that each view shows the object all the way through as if it were transparent:
Planar
Horizontal
Auxiliary
Orthographic
This is the most common application for developments and intersections:
Sheet metal construction
Piping
Architecture
Mechanical engineering
The Offset tool should only be used for placing ________ in an isometric drawing.
Circles
Horizontal lines
Vertical lines
None of the above
A fillet is a rounded surface on the ________ corner of a part.
Inside
Outside
Radial
Isoplane
This type of axonometric drawing has equal foreshortening along two axis directions and a different amount on the third axis:
Dimetric
Multiview
Isometric
Trimetric
In a CAD system, you can draw an ellipse by specifying these:
The bounding lines
The midpoint and end points
The center and major and minor axes
The center and radius
Approximately this much of the cost of product development and manufacture is determined at the design stage:
40-50 %
60-75 %
70-80 %
75-85 %
A ________ is the person responsible for verifying that the drawings in a project set are free of mistakes.
Client
CAD trainee
Receptionist
Checker
An accurate record of changes made to release drawings is tracked via this:
A revision block
The basic title form
Working drawings
Portable documents
The MASSPROP shortcut will provide the following information.
Mass
Volume
Bounding box
All of the above
The Free Orbit tool is found on the ________ toolbar.
Rotate
Move
Modify
3-D Move
One way to evenly space dimensions on a drawing is to use the ________.
Dimension Space tool
Linear tool
Continue tool
Baseline tool
Inserting blocks into a drawing file usually requires exacting placement. The drafter should insure that ________ is turned on.
O Snaps
Ortho
Grid
Dynamic Input
Geometric primitives include shapes such as ________.
Boxes
Cylinders
Wedges
All of the above
In multi-view drawing it is common practice to include three views, the front, the top and the right side. If no dimensions are required on the right side view the drafter can ________.
Leave the view as is
Eliminate the view
Use the left view instead
None of the above
To insure that everyone understands what the electrical symbols represent it is customary to include a ________ on the electrical sheet.
List
Part number
Electrical legend
Electrical layer
The type of line that projects from an object for the express purpose of locating a dimension is a ________ line.
Visible
Hidden
Extension
Dimension
This type of projection is when projectors are parallel to each other, but is at an angle other than 90 degrees to the plane of projection:
Oblique projection
Perpendicular projection
Aesthetic projection
Angular projection
A secondary auxiliary view is a projection off of the ________.
Front view
Top view
Primary auxiliary view
None of the above
Using the Relative Polar Coordinate System to add a 3 inch line that is 45 degrees from the end point of the line created above the drafter would ________.
Type @3<45 and enter
Type 3 back slash and enter
Type 3 forward slash and enter
Type 3 and try to use the Dynamic Input readout to find the end point
A back or backing weld is a type of:
Groove weld
Resistance weld
Arc and gas weld
Upset weld
If a designer is developing a plan for a project in which the entire part is made out of ¾ thick plywood and he only wants to use one view, he should use the ________ view.
Front
Top
Right
Back
Switches and relays should be shown in this position with no operating force or applied energy:
Normal
Closed
Offset
Application
The condition of a part when it contains the least amount of material is referred to as ________.
Smallest
LMC
MMC
Actual size
The foundation contractor will work with the following architectural plans.
Foundation
Site plan
Floor plan
All of the above
Oblique drawings are dimensioned in a similar fashion as these types of drawings:
Orthographic
Isometric
Angular
Parallel
A full scale technical drawing will have a scale factor of ________.
1 : 1
1 : 2
2 : 1
1 : 4
In order to create an isometric circle to represent a hole through the top surface of a box, the drafter must insure that the correct iso-plane has been selected by scrolling through the iso-planes using the ________ key.
F1
F3
F5
F8
This is a conical-shaped recess around a hole, often used to receive a tapered screw head:
Boss
Spotface
Counterbore
Countersink