Related Questions
What is the correct answer?
4
If a plane is parallel to the plane of projection, it appears:
What is the correct answer?
4
In an exploded assembly drawing it is customary for the drafter to use a ________ line to illustrate how parts fit together.
What is the correct answer?
4
The edges of a cube in isometric projection make angles of this many degrees with each other:
What is the correct answer?
4
Architectural dimensioning is usually done in ________.
What is the correct answer?
4
This material is used in masonry construction, most commonly for ornamental facing:
What is the correct answer?
4
A line drawn with a long section, short dash, and another long section is a ________.
C. Center axis of a hidden cylinder
What is the correct answer?
4
The ________ is a standard element of a section view in a technical drawing.
C. Material hatch pattern
What is the correct answer?
4
One way to evenly space dimensions on a drawing is to use the ________.
What is the correct answer?
4
When using the direct entry method to create a horizontal line exactly three inches long the drafter should ________ first.
A. Pull the line from away from the starting point very carefully
B. Insure that Ortho is on
C. Enter 3 for the length of the line
D. Read the coordinate position on the Dynamic Readout
What is the correct answer?
4
This is the intersection of the ground plane with the picture plane:
What is the correct answer?
4
Switches and relays should be shown in this position with no operating force or applied energy:
What is the correct answer?
4
Spur gear design normally begins with selecting this:
What is the correct answer?
4
A civil engineer working on a bridge design would probably rely on his ________ scale for checking printed drawings.
What is the correct answer?
4
This line pattern is composed of three dashes, one long dash on each end with a short dash in the middle:
What is the correct answer?
4
When creating an isometric drawing in Auto-CAD the drafter can utilize the Dynamic Input and Polar Coordinate system to place both vertical and horizontal lines. A line created from one point 3 inches at 180 degrees would be a ________ line.
What is the correct answer?
4
In U.S. structural and architectural drafting, all dimensions of this length are usually expressed in feet and inches:
What is the correct answer?
4
How can the drafter prevent Auto-CAD from placing or stacking another center mark on a circle when adding a diameter dimension to it?
A. Explode the dimension and then erase the center mark
B. Use the Properties dialog box to turn off the center mark of the dimension
D. Use the trim tool to take away the stacked center mark
What is the correct answer?
4
When creating your own blocks it is important to avoid drawing any portion of the block in the ________ layer.
What is the correct answer?
4
This type of drawing is created to calculate areas, locate property lines, and locate building projects and facilities:
What is the correct answer?
4
Once a drawing is determined to be complete, the title block is used to document the change from:
A. A draft to a finished drawing
B. A finished to a working drawing
C. An assembly to a finished drawing
D. A working drawing to a draft
What is the correct answer?
4
The most common geometric form used in gears today is this:
What is the correct answer?
4
The first step in creating a traditional technical drawing is to ________.
A. Draw a series of guide lines
C. Align the paper so that it will be positioned square to the parallel bar
D. Sharpen the leads in the technical pens
What is the correct answer?
4
This is the plane upon which the top view is projected:
What is the correct answer?
4
When the receding lines are true length, and the projectors are at 45 degrees to the plane of projection, the oblique drawing is called this:
C. Axonometric projection
What is the correct answer?
4
The organized and orderly approach to solving problems is known as the:
What is the correct answer?
4
To avoid having to dimension to a hidden feature the drafter can utilize a ________ section.
What is the correct answer?
4
The primary unit of measurement for engineering drawings and design in the mechanical industries is the:
What is the correct answer?
4
Once the architect has finalized the house plans with the client any changes to the design requested by the client will require a ________.
C. Whole new set of drawings
What is the correct answer?
4
The text height for room names should be set to ________for a drawing that will be plotted to a scale of ¼ = 1'-0.
What is the correct answer?
4
This is the theoretically exact size from which limits of size are determined: