Related Questions
What is the correct answer?
4
A line with a tapering width can be easily created by using the __________ tool.
What is the correct answer?
4
Students can complete an associate's degree in drafting which normally takes about ________ years to complete.
What is the correct answer?
4
An Auto-CAD term that refers to a pre-drawn object which is stored in a drawing file and can be inserted into any other drawing file as needed is a ________.
What is the correct answer?
4
The thread note for a typical bolt will include the ________.
A. Major diameter of the thread
What is the correct answer?
4
Angles project true size only when the plane containing the angle and plane of projection are this:
What is the correct answer?
4
Architectural drawings used to construct a house are often plotted with a scale of ¼ = 1'-0. What scale is this?
What is the correct answer?
4
In a CAD system, you can draw an ellipse by specifying these:
B. The midpoint and end points
C. The center and major and minor axes
What is the correct answer?
4
Architectural dimensioning standards allow for the placement of dimensions inside the floor plan. These inside dimensions locate interior __________.
A. Door openings and walls
What is the correct answer?
4
Acceptable parts must not extend beyond this:
What is the correct answer?
4
The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.
What is the correct answer?
4
Some common blocks used by architectural drafters include ________.
What is the correct answer?
4
The typical parts list should include the ________.
B. Manufacturing material
C. Number of parts needed
What is the correct answer?
4
These maps are used to plan construction projects that locate construction features so they fit the topography of the area:
C. Structural topography maps
D. Structure location plans
What is the correct answer?
4
The ________ tool on the Dimension tool bar places the length of an arch on a drawing.
What is the correct answer?
4
When positioning this feature of perspective projection, the centerline of the cone of visual rays should be directed toward the approximate center of the object:
What is the correct answer?
4
Which of the following is one of the basic types of welded joints:
What is the correct answer?
4
If a plane is parallel to the plane of projection, it appears:
What is the correct answer?
4
When using the descriptive geometry method to create an auxiliary view the drafter should __________.
A. Rotate the snap grid to the same angle of the inclined plane
B. Offset the right vertical line of the front view
C. Rotate the top line of the front view 45 degrees
D. Offset the top line of the front view 2 inches
What is the correct answer?
4
This type of drawing shows two lines representing the pipe diameter:
What is the correct answer?
4
When dimensioning piping drawings, you give the lengths of all runs of this type:
What is the correct answer?
4
The ________ tool on the Dimension tool bar will place several dimensions at one time by using a selection box placed over several part features.
What is the correct answer?
4
This type of section is not in direct projection from the view containing the cutting plane:
What is the correct answer?
4
When the drafter types the word BLOCK or selects the Make Block tool from the Draw tool bar the ________ will appear.
C. Block Definition Dialog
What is the correct answer?
4
When drawing a line using the relative coordinate system a line is created from ________.
B. The ending point of the last line
C. The beginning point of the last line
What is the correct answer?
4
The MASSPROP shortcut will provide the following information.
What is the correct answer?
4
Isometric drawings are often used by ________ to help illustrate complex designs.
What is the correct answer?
4
In multi-view drawing it is common practice to include three views, the front, the top and the right side. If no dimensions are required on the right side view the drafter can ________.
C. Use the left view instead
What is the correct answer?
4
A drafter who develops technical drawings of a highway overpass would most likely be a ________ drafter.
What is the correct answer?
4
On a floor plan the dashed line that appears approximately 24 outside the exterior wall represents the __________.
What is the correct answer?
4
Center lines are used to locate or represent the centers of ________.