Related Questions
What is the correct answer?
4
Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of
What is the correct answer?
4
Thermit welding is categorised as the __________ welding.
What is the correct answer?
4
Common salt is produced from sea water in India generally by the __________ method.
What is the correct answer?
4
In practice, the compression ratio of compression-ignition (CI) engine ranges from
What is the correct answer?
4
Otto cycle used in spark ignition petrol engines is also known as the constant __________ cycle.
What is the correct answer?
4
The bank of tubes located at the back of the domestic refrigerators are the __________ tubes.
What is the correct answer?
4
Which of the following contributes maximum as main source of sulphur in the blast furnace charge?
What is the correct answer?
4
The main constituent of bones is
What is the correct answer?
4
In a totally irreversible isothermal expansion process for an ideal gas, ΔE = 0, ΔH = 0. Then ΔQ and ΔS will be
What is the correct answer?
4
Catalyst used in the catalytic converter employed in automobiles to convert CO into CO2 and for complete oxidation of un-burnt hydrocarbons is
What is the correct answer?
4
Which of the following forces does not act on a fluid at rest?
What is the correct answer?
4
Lead is poured into the joint between two __________ pipes.
What is the correct answer?
4
The delivery pressure of boiler feed water pump compared to the boiler steam pressure is
What is the correct answer?
4
Hot extrusion process is not used for making
A. Cast iron pipe for domestic water supply
B. Aluminium curtain rods
C. Stainless steel tubes used in furnitures
What is the correct answer?
4
For separating small pieces of metal from engine oil of a car, the best separating technique is the
D. Fractional distillation
What is the correct answer?
4
__________ test can be termed as the semidestructive test.
What is the correct answer?
4
A solution which resists change in its pH value on addition of acid/alkali is called the __________ solution.
What is the correct answer?
4
The best guide to judge the general quality of water is the measurement of its
B. Electrical conductivity
D. Dissolved oxygen content
What is the correct answer?
4
Auto collimator is used to check
What is the correct answer?
4
For grinding of softer materials, the grinding wheel should have __________ grain size.
What is the correct answer?
4
A material is capable of resisting softening at high temperature, because of its property termed as
What is the correct answer?
4
Limestone addition in the blast furnace is done to flux __________ present in the raw materials.
What is the correct answer?
4
Hollow shafts can be made as strong as solid shafts by making the twisting moments of both the shafts same. Shafts made by __________ have residual stresses.
What is the correct answer?
4
For the irreversible reaction, Ca+ 2C = Ca C2 , Δ H°298 = - 60000 J . mole-1 . If a system initially containing 2 moles of calcium, 3 moles of carbon and 1 mole of calcium carbide is allowed to react to completion, the heat evolved at 298 K will be
What is the correct answer?
4
Iron content in Indian iron ore is about __________ percent.
What is the correct answer?
4
Shrinkage allowance on pattern is provided to compensate for shrinkage when the
A. Metal changes from liquid state to solid state at freezing temperature
B. Solid phase temperature drops from freezing temperature to the room temperature
C. Liquid metal temperature drops from pouring temperature to room temperature
D. Liquid metal temperature drops from pouring temperature to freezing temperature
What is the correct answer?
4
An example of unsteady non uniform flow is the flow of liquid under pressure through a
A. Tapering pipe at constant flow rate
B. Tapering pipe at either decreasing or increasing flow rate
C. Long pipeline of constant diameter
What is the correct answer?
4
The minimum temperature to which the water can be cooled in a cooling tower is the __________ temperature of air.
What is the correct answer?
4
The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
What is the correct answer?
4
The temperature at which the magnetic property of iron disappears (i.e., it becomes non-magnetic) and its electrical conductivity & specific heat also changes, is called the 'Curie point', which is __________ °C.