Related Questions
What is the correct answer?
4
Moist climate is the most favourable factor in the site selection far a
What is the correct answer?
4
In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are.
A. μ , α and θ all have units of m/s
B. μ , α and θ all have units of m2/s
C. α and θ have units of m2/s, while μ has unit of m/s
D. α and θ have units of m/s, while μ has unit of m2/s
What is the correct answer?
4
Steel produced from phosphatic iron is __________ in nature.
What is the correct answer?
4
Which of the, following is not associated with the functioning of a petrol engine?
A. Compression ignition system
What is the correct answer?
4
In extrusion of metals, which of the following statement is true?
A. Speed of the extruded material is same as that of ram speed
B. Redundant work is a function of the die angle
C. Relative motion between the billet surface and the container wall is always present
D. Hollow ram is used for indirect extrusion
What is the correct answer?
4
Pick out the wrong statement about the machinability of metals. Machinability of a metal
A. Decreases with increase in strain hardening tendencies
B. Decreases with increase in hardness, in general
C. Depend on the composition, microstructure and physical & mechanical properties
D. Decreases with increases in tensile strength & decrease in grain size
What is the correct answer?
4
The best lubricants for a machine working at high temperature & load is
What is the correct answer?
4
__________ is not used as a material of construction in thermocouples.
What is the correct answer?
4
Which of the following processes follows the hardening process for reducing the hardening strains & increasing the toughness of the steel part?
What is the correct answer?
4
Which of the following fastening devices has a head at one end and a nut fitted to the other?
What is the correct answer?
4
__________ property of a material is determined by the Herbert Pendulum device.
What is the correct answer?
4
A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient.
B. Inversely proportional to
C. Directly proportional to
What is the correct answer?
4
A metal having a Poisson's ratio = 0.3 is elastically deformed under uniaxial tension. If the longitudinal strain = 0.8, then the magnitude of thickness strain is
What is the correct answer?
4
Flue gases pass through the following boiler accessories in a high pressure natural circulation boiler.
A. Induced draft fan
B. Economiser
C. Air preheater
D. Steam superheater Which of the following gives the correct sequence of flow of the flue gases through the above mentioned boiler accessories?
What is the correct answer?
4
Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs?
What is the correct answer?
4
Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2)?
What is the correct answer?
4
As the fluid flow rate increases, the float of the Rotameter
B. Rotates at higher speed
C. Rotates at lower speed
D. Drops down in the tube
What is the correct answer?
4
Which of the following materials has the maximum shrinkage allowance?
What is the correct answer?
4
The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the
D. Stress recovery effect
What is the correct answer?
4
__________ furnace is generally used in the non-ferrous foundries.
What is the correct answer?
4
The elastic strain energy of a unit length of an edge dislocation as compared to that of a screw dislocation is
What is the correct answer?
4
Cassiterite is an ore of
What is the correct answer?
4
Which of the following rays has the least wavelength?
What is the correct answer?
4
Dryness fraction of dry steam is
What is the correct answer?
4
Enzymes belong to the category of
What is the correct answer?
4
An alloy of Fe - 0.4 % C is
What is the correct answer?
4
The units of the rate constant for a second order reaction are
What is the correct answer?
4
An abrupt and sudden fall in the reading of barometer is an indication of the
What is the correct answer?
4
Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about
What is the correct answer?
4
Solidification time of a molten metal in a casting is proportional to (where, V = volume of metal & A = its surface area; in the casting)