Related Questions
What is the correct answer?
4
The behaviour of a metal specimen, which when plastically strained in tension reduces its yield stress in compression and vice versa; is termed as the
D. Stress recovery effect
What is the correct answer?
4
CANDU type nuclear reactor using natural uranium as fuel is the extensively used nuclear reactor because of the fact that the
A. Specific fuel consumption is very low due to the use of heavy water
B. Fuel cost is much lower than that used in pressurised water or boiling water reactor
C. Heavy water is used both as coolant as well as moderator
What is the correct answer?
4
Which of the, following is not associated with the functioning of a petrol engine?
A. Compression ignition system
What is the correct answer?
4
Difference at any instant between the value of the controlled variable and the set point is called the
What is the correct answer?
4
__________ is not a case hardening process.
What is the correct answer?
4
Chlorine acts as a bleaching agent only in the presence of
What is the correct answer?
4
Suitability of steel for its use in cable is judged by its strength in
What is the correct answer?
4
Cupola produces __________ iron.
What is the correct answer?
4
Which of the following is not an explosive?
What is the correct answer?
4
Heat release during phase change is observed in case of a/an
What is the correct answer?
4
An oxidation process is accompanied with decrease in the
What is the correct answer?
4
Density in the solid state is slightly less than that in its liquid state, in case of
What is the correct answer?
4
With increase in impurities in metals, their corrosion resistances
D. May increase or decrease; depending on the type of metal
What is the correct answer?
4
Maximum permissible sulphur content in steel is __________ percent.
What is the correct answer?
4
Hot working of lead is carried out at
What is the correct answer?
4
The only suitable method for hardening the low carbon steel is case hardening. Which of the following is a case hardening process?
What is the correct answer?
4
The activity of pure hydrogen gas at 1000°C and 5 atm pressure
B. Is always greater than 1
D. Depends on the choice of the standard state
What is the correct answer?
4
The refractory lining of the bottom in a basic electric arc furnace is made of
What is the correct answer?
4
Use of water as a manometric liquid suffers from the disadvantage of its
What is the correct answer?
4
__________ of air does not increase with increase in temperature.
What is the correct answer?
4
The most serious manufacturing defect from fracture toughness point of view is
What is the correct answer?
4
A metal having a Poisson's ratio = 0.3 is elastically deformed under uniaxial tension. If the longitudinal strain = 0.8, then the magnitude of thickness strain is
What is the correct answer?
4
Steels with high carbon equivalent have poor Weldability, because in these steels during welding
A. Carbon and other alloying elements get oxidised from the weld pool
B. Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld
C. Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld
D. Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld
What is the correct answer?
4
The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as
What is the correct answer?
4
L.D. (Linz-Donawitz) converter is used in the production of
What is the correct answer?
4
Property responsible for the talcum powder to cling to the skin is the
What is the correct answer?
4
With increase in __________ Knocking tendency in a spark ignition petrol engine decreases.
What is the correct answer?
4
Limestone addition in the blast furnace is done to flux __________ present in the raw materials.
What is the correct answer?
4
Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is
What is the correct answer?
4
Transformer cores are normally made from
C. Grain oriented Fe-Si alloy