Related Questions
What is the correct answer?
4
Ammonia gas can be dried by
What is the correct answer?
4
Hot extrusion process is not used for making
A. Cast iron pipe for domestic water supply
B. Aluminium curtain rods
C. Stainless steel tubes used in furnitures
What is the correct answer?
4
Which of the following does not discharge the dust collected as a dry solid?
A. Electrostatic precipitator
D. Gravity settling chamber
What is the correct answer?
4
Heat transfer to the water wall in a high pressure water wall type boiler furnace is mainly by
What is the correct answer?
4
In practice, the compression ratio of compression-ignition (CI) engine ranges from
What is the correct answer?
4
Projection welding & stud welding is categorised as the __________ welding.
What is the correct answer?
4
__________ has a negative co-efficient of linear expansion.
What is the correct answer?
4
Magnetic permeability of iron is increased by its
D. Alternate heating & cooling
What is the correct answer?
4
Which of the following is a boiler accessory
i.e., not a boiler mounting?
What is the correct answer?
4
Dislocations are __________ defects.
What is the correct answer?
4
Reduction in the grain size reduces the __________ of the material.
What is the correct answer?
4
Non-ferrous alloys used for making cutting tools need not have high
What is the correct answer?
4
With increase in temperature, the surface tension of water
What is the correct answer?
4
Pick out the correct statement about the condensation.
A. Filmwise condensation gives a lower heat transfer rate than the dropwise condensation
B. Suitable coating or vapour additive is used to promote film wise condensation
C. If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it
D. Reynolds number of condensing liquid is based on its mass flow rate
What is the correct answer?
4
The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be
What is the correct answer?
4
Half life of a radioactive isotope corresponds to the time required for half of the __________ to decay.
What is the correct answer?
4
A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C.
What is the correct answer?
4
The majority charge carriers in p-type silicon are
What is the correct answer?
4
Which of the following processes follows the hardening process for reducing the hardening strains & increasing the toughness of the steel part?
What is the correct answer?
4
A solid aluminium ball, when quenched in a water bath maintained at 40°C, cools down from 550°C to 450°C in 20 seconds. The expected temperature of the ball after next 20 seconds may be about __________ °C.
What is the correct answer?
4
Co-efficient of performance of a Carnot cycle refrigerator operating between - 23°C and + 27°C is
What is the correct answer?
4
Pick out the correct statement.
A. Hot worked materials are subjected to annealing to remove internal stresses
B. Annealing of steel hardens it slightly
C. Normalising of a material induces stresses
D. Tempering of a material improves ductility & toughness but reduces hardness & brittleness
What is the correct answer?
4
Which of the following metals reacts violently with water?
What is the correct answer?
4
Annealing of cast iron
A. Softens it to facilitate machining
B. Decreases the free carbon
C. Increases the strength
What is the correct answer?
4
Which of the following performance characteristics of a S.I engine is not affected by the front end volatility of the petrol used?
What is the correct answer?
4
__________ glass is used in the mercury in glass thermometer meant for measuring a temperature of 500°C.
What is the correct answer?
4
The passage between the nozzle and the __________ is called 'sprue' in case of injection moulding.
What is the correct answer?
4
The most important requirement for aluminium industry is the availability of cheap
What is the correct answer?
4
Powder metallurgy process does not make metal powder by
D. Electrolytic deposition
What is the correct answer?
4
For efficient performance of a blast furnace, the extent of reduction of Wustite (FeO) should be
A. 100% indirect reduction
C. 50-60% indirect reduction
D. 30-40% indirect reduction