Related Questions
What is the correct answer?
4
Coating thickness in case of galvanising of steel sheet generally corresponds to the deposition of __________ gms of zinc per of steel strip.
What is the correct answer?
4
The leaching solvent used in Baeyer's process for the purification of bauxite is
What is the correct answer?
4
Sudden fall of atmospheric pressure by a large amount is an indication of the
What is the correct answer?
4
The temperature at which ferromagnetic material can no longer be magnetised by the outside forces, is termed as the
What is the correct answer?
4
A material being tested for endurance strength is subjected to the __________ load.
What is the correct answer?
4
Mild steel has __________ crystal lattice structure.
A. Face centred cubic (fcc)
B. Body centred cubic (bcc)
What is the correct answer?
4
A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient.
B. Inversely proportional to
C. Directly proportional to
What is the correct answer?
4
Heat release during phase change is observed in case of a/an
What is the correct answer?
4
Large scale fire on fuel gas line is normally extinguished by
What is the correct answer?
4
Wrought iron is not
A. Ductile & resistant to corrosion/rusting
C. Having uniform strength in all directions
D. Having maximum tensile strength along the lines of slag distribution
What is the correct answer?
4
Which of the following materials has the poorest electrical conductivity?
What is the correct answer?
4
Corrosion rate cannot be lowered by reducing the __________ of the corroding medium.
What is the correct answer?
4
Age hardening is connected with
What is the correct answer?
4
Most important property of steels for use in automobile bodies is the
What is the correct answer?
4
There are one octahedral void and __________ tetrahedral void in the closest packing of atoms.
What is the correct answer?
4
Yield strength of a polycrystalline metal with an average grain size d, is proportional to
What is the correct answer?
4
A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre.
What is the correct answer?
4
For dynamic strain measurement, the Wheatstone bridge used is of __________ type.
A. Voltage sensitive null
B. Voltage sensitive deflected
C. Current sensitive deflected
What is the correct answer?
4
Moist climate is the most favourable factor in the site selection far a
What is the correct answer?
4
Addition of __________ to steel does not help in improving its machinability.
What is the correct answer?
4
On being hit with a hammer, __________ will readily fracture.
What is the correct answer?
4
For which pair of the fuel gases, calorific value (C.V.) of one fuel is almost double that of the other on volume basis (i.e., kcal/Nm3) while the C.V. is same on weight basis (i.e., kcal/kg)?
C. Sewage gas and gobar gas
D. B.F gas and coke oven gas
What is the correct answer?
4
Runge-Kutta method is used to solve a/an
A. Ordinary differential equation of nth order
B. Simultaneous non-linear equation
C. Linear differential equation
What is the correct answer?
4
__________ pipe is the most suitable for carrying sanitary drainage.
B. Reinforced cement concrete
What is the correct answer?
4
The amount of different substances produced, when the same quantity of electricity is passed through different solutions are proportional to their
What is the correct answer?
4
In case of water (Prandtl number ≈ 6) flowing over a flat plate heated over the entire length, the thermal boundary layer thickness as compared to hydrodynamic boundary layer thickness is
What is the correct answer?
4
In troposphere (the weather domain), the temperature 't' at height 'h' above the sea level in metres is given by (where, temperature at sea level is 15°C and t is in °C.)
What is the correct answer?
4
Which of the following hardness tests does not measure the indentation hardness of metals and alloys?
B. Shore scleroscope test
D. Rockwell hardness test
What is the correct answer?
4
'GASOHOL' widely used in Brazil as a motor fuel is a mixture of alcohol and
C. Light hydrocarbon gases (e.g. butane or propane)
What is the correct answer?
4
Shaft/rotor speed is most accurately measured by a