Related Questions
What is the correct answer?
4
Work done by a/an __________ process is determined by ∫p. dv
What is the correct answer?
4
Two wires of the same radius & material having length in the ratio of 1 : 2 are stretched by the same force. The strain produced in the two wires will be in the ratio of
What is the correct answer?
4
If a solid is compressed adiabatically in its elastic range, its __________ remains constant
What is the correct answer?
4
The taper provided on pattern for its easy & clean withdrawal from the mould is termed as the __________ allowance.
What is the correct answer?
4
A form of stress corrosion failure termed as 'season cracking' is generally observed in
A. Thermosetting polymers
What is the correct answer?
4
Ferromagnetic materials owe their properties to __________ inner sub-shells.
What is the correct answer?
4
Cold heading or upsetting is categorised as the __________ process.
What is the correct answer?
4
Stainless steel is welded with difficulty because of
A. Its high melting temperature
D. Chromium carbide formation
What is the correct answer?
4
Lead is added to 60:40 brass primarily to improve
What is the correct answer?
4
In the blast furnace, incorporation of water vapour in the blast gives the following effect.
A. Increases the reducing potential of the gas
B. Increases the flame temperature
C. No significant change occurs
D. Increases the hydrogen content in the metal
What is the correct answer?
4
During sensible heating of humid air
A. Relative humidity increases
B. Dew point remains constant
C. Dry bulb & wet bulb temperature increases
What is the correct answer?
4
X-rays are
D. Of higher wavelength than visible light
What is the correct answer?
4
__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength.
What is the correct answer?
4
The most abundant metal present in the earth's crust is;
What is the correct answer?
4
Half life of a radioactive isotope corresponds to the time required for half of the __________ to decay.
What is the correct answer?
4
Pearlite comprises of
A. 87% cementite & 13% Fe
B. 87% ferrite & 13% cementite
C. 93.33% ferrite & 6.67% C
What is the correct answer?
4
Heat transfer by __________ is almost absent in case of fluidised bed drying operation.
What is the correct answer?
4
__________ number determines whether the fluid flow in an open channel is supercritical, critical or sub-critical.
What is the correct answer?
4
Which of the following is the correct nature of shear stress distribution along the cross section in a horizontal circular pipe under steady state fluid flow condition?
What is the correct answer?
4
The most suitable material of construction for a sewer to carry sewage under high pressure is
What is the correct answer?
4
Ammonia gas can be dried by
What is the correct answer?
4
Temperature of hot gases flowing in a pipe is measured by a thermocouple inserted in the thermal well. The thermal well made of __________ will facilitate the most accurate measurement of the temperature.
What is the correct answer?
4
Minimum number of members required to form a Public Limited Joint Stock Com-pany is
What is the correct answer?
4
Most of the phosphorous present in the blast furnace burden enters into
What is the correct answer?
4
Annealing of white cast iron produces __________ iron.
What is the correct answer?
4
Dislocation cross-slip is difficult in those materials, which have
A. Large number of slip systems
B. High work hardening rate
D. Low stacking fault energy
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called
What is the correct answer?
4
__________ fluid force is not considered in the Navier-Stokes equation.
What is the correct answer?
4
Pick out the correct combination about the role of various additives used in polymers.
A. Plasticiser: increases the polymer strength
B. Heat stabiliser: increases the maximum service temperature
C. Fillers: Does not affect the property of polymer but increases its weight
D. Lubricants: increases the flexibility of polymers
What is the correct answer?
4
Euler number is defined as the ratio of inertia force to __________ force.