Related Questions
What is the correct answer?
4
The most commonly used moderator in nuclear power plants is
What is the correct answer?
4
The type of pump used for lifting large quantity of sewage is a __________ pump.
What is the correct answer?
4
Corona discharge is related to the operation of a/an
B. Electrostatic precipitator
D. Magneto hydrodynamic generator (MHD)
What is the correct answer?
4
The concentration of (H+) ions is 4 x 10-5 in a solution. Then pH of the solution will be (Given log 4 = 0.6)
What is the correct answer?
4
__________ circuit is most commonly used to measure strain with the help of a strain gauge.
B. Voltage balancing potentiometric
C. Simple current sensitive
What is the correct answer?
4
Resilience of a bolt can be increased by increasing its
What is the correct answer?
4
The noble metals
A. Are exemplified by Na, K and Li
B. Do not resist corrosion very strongly
C. Are the lowermost in the electro-chemical series of metals
What is the correct answer?
4
Which of the following is not used as a bearing material?
What is the correct answer?
4
A gas which is collected over water becomes moistened due to water vapor, exerts its own partial pressure at the gas temperature, which is termed as its
What is the correct answer?
4
The excess air required for the combustion of pulverised coal is of the order of about __________ percent.
What is the correct answer?
4
Pick out the wrong statement.
A. Ductile fracture of a stressed material, which exhibits a large plastic deformation is commonly caused by the formation and coalescence of voids in the necked region
B. Brittle fracture is caused by the propagation of pre-existing cracks in the material and involves minimum plastic deformation
C. Fatigue fracture of a material is always brittle in nature and takes place due to the existence of line imperfections
D. Brittle materials are generally tested in tension
What is the correct answer?
4
Specific __________ is a dimensionless quantity.
What is the correct answer?
4
Copper deposits are found in India at the following location:
What is the correct answer?
4
Percentage of differential pressure lost in a Venturimeter with a tapering of 15° may be about
What is the correct answer?
4
In case of condensers & evaporators operating under given terminal conditions, LMTD (logarithmic mean temperature difference) for counter flow as compared to that for parallel flow is
What is the correct answer?
4
As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint.
What is the correct answer?
4
Plasma is
A. A high temperature neutral gas
B. Nothing but ionised gas
C. A source of steady and highest controllable pressure
D. Formed at very low temperature
What is the correct answer?
4
Lead is poured into the joints between two __________ pipes.
What is the correct answer?
4
Non-ferrous alloys used for making cutting tools need not have high
What is the correct answer?
4
High endurance limit of carburised machine parts is because of the fact that carburisation
A. Suppresses any stress concentration produced in the parts
B. Enhances the yield point of the material
C. Introduces a compressive layer on the surface
D. Produces a better surface finish
What is the correct answer?
4
Cementite is in the lamellar form in the __________ phase of steel.
What is the correct answer?
4
Yield strength of a material is determined by the __________ test.
What is the correct answer?
4
Cold chisels hammers are made of
What is the correct answer?
4
One face of a furnace wall is at 1030°C and the other face is exposed to room temperature (30°C). If the thermal conductivity of furnace wall is 3 W. m- 1. k-1 and the wall thickness is 0.3 m, the maximum heat loss (in W/m) is
What is the correct answer?
4
Fibre glass is a composite material of
A. Glass fibre in a polymer matrix
B. Glass fibre in a metallic matrix
C. Polymer fibre in a glassy matrix
What is the correct answer?
4
Lead is added to 60:40 brass primarily to improve
What is the correct answer?
4
__________ has a negative co-efficient of linear expansion.
What is the correct answer?
4
A polymer is termed as an 'elastomer', if its percentage elongation is more than 100%. An elastomer is termed as 'rubber' if its percentage elongation is more than __________ percent.
What is the correct answer?
4
Powder metallurgy technique is used in the production of __________ tools.
What is the correct answer?
4
The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be