Related Questions
What is the correct answer?
4
Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)?
What is the correct answer?
4
The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the
What is the correct answer?
4
Stainless steel is welded with difficulty because of
A. Its high melting temperature
D. Chromium carbide formation
What is the correct answer?
4
Brittleness induced due to the presence of sulphur in steel can be reduced by adding
What is the correct answer?
4
An example of unsteady non uniform flow is the flow of liquid under pressure through a
A. Tapering pipe at constant flow rate
B. Tapering pipe at either decreasing or increasing flow rate
C. Long pipeline of constant diameter
What is the correct answer?
4
Addition of __________ to steel does not impart hardness.
What is the correct answer?
4
Internal energy of a gas obeying Van-Der- Waals equation of state, [p + (a/v2)] (V - b) = RT, depends upon its
A. Pressure & temperature
B. Pressure & specific volume
C. Temperature & specific volume
What is the correct answer?
4
The amount of different substances produced, when the same quantity of electricity is passed through different solutions are proportional to their
What is the correct answer?
4
The lightest non-inflammable gas is
What is the correct answer?
4
Exposure to __________ accelerates the degradation of plastics.
B. High atmospheric temperature
C. High ambient temperature
What is the correct answer?
4
Normalising does not __________ of a metal.
A. Improve machinability & tensile strength
B. Remove internal stresses
D. Remove strains caused by cold working
What is the correct answer?
4
'Cryogenics' is concerned with the generation & use of low temperature in the range of
What is the correct answer?
4
Electrometallurgy is not involved in the extraction of __________ from its ore.
What is the correct answer?
4
Function of gear box is to
What is the correct answer?
4
The value of for air & most common gases can be safely assumed to be
What is the correct answer?
4
All of the following alloying elements of steel increases hardness but sacrifice ductility, except
What is the correct answer?
4
Yield strength of a polycrystalline metal with an average grain size d, is proportional to
What is the correct answer?
4
Which of the following forces does not act on a fluid at rest?
What is the correct answer?
4
Saturated steam at a pressure of 25 kg/cm2 is throttled to attain 5 kg/cm2. Then the outcoming steam will be
What is the correct answer?
4
Which of the following is an acidic constituent of B.F. slag?
A.
What is the correct answer?
4
Difference at any instant between the value of the controlled variable and the set point is called the
What is the correct answer?
4
Alcohols are not suitable as diesel engine fuel because the cetane number of alcohols is
A. Very low which prevents their ignition by compression
B. Very high which prevents their ignition by compression
What is the correct answer?
4
The most suitable material of construction for a sewer to carry sewage under high pressure is
What is the correct answer?
4
Latent heat of dry steam at atmospheric pressure is 539 Kcal/kg; which __________ with increase in the pressure of steam.
D. May increase or decrease
What is the correct answer?
4
Fire refining process is employed in case of
What is the correct answer?
4
In a furnace with heating element temperature at 1700°C, the dominant mechanism of heat transfer will be
What is the correct answer?
4
The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler.
B. Evaporation efficiency
What is the correct answer?
4
Leakage in a cooking gas cylinder is detected by
B. Pouring soap solution on the surface and locating the gas bubbles
D. Pungent smell of mercaptans present in the gas
What is the correct answer?
4
Unbreakable crockeries are made from __________ polymers.
What is the correct answer?
4
Which of the following is not a ferromagnetic material?