RIP supports load balancing for up to __________ ___________ paths.
Six, unequal-cost
Four, unequal-cost
Four, equal-cost
Six, equal-cost
Correct Answer :
D. Six, equal-cost
Related Questions
You have a total of five routers. ________ circuits are required to fully mesh the network, where every router needs ___________ interfaces.
5, 5
8, 4
10, 5
10, 4
What subnet mask would you use to set up a default route?
0.0.0.0
255.255.255.255
Depends on the type of network number
None of these answers
Which router command would take you back to a suspended telnet session?
reconnect
connect
resume
toggle
Which is not one of the three main functions of a layer-2 device?
Learning
Forwarding
Listening
Removing loops
When choosing a dynamic routing protocol, which of the following should not be considered?
Metrics used
How routing information is shared
How routing information is processed
Number of PCs in the network
If you enter a command in either User EXEC mode or Privilege EXEC mode that the IOS does not recognize, the switch or router
Logs you out
Tries to resolve the command to an IP address
Executes the closest command that it can find in its command set
Makes a "beep" sound
__________ states that if a neighboring router sends a route to a router, the receiving router will not propagate this route back to the advertising router on the same interface.
Split horizon
Poison reverse
Hold-down timer
Hop count limit
You are given a Class C network with a subnet mask of 255.255.255.248. How many host addresses are there on each subnet?
4
6
8
14
VLSM allows you to summarize __________ back to the class boundary.
Subnets
Networks
You are at User EXEC mode and type the letter e. What message appears?
% Incomplete command.
% Ambiguous command:
% Unknown command or computer name
% Invalid input detected at '^'.
Which IGRP command allows unequal-cost load balancing?
variance
load
balance
network
Which controller command specifies how ones and zeros are represented on a digital circuit?
framing
linecode
clock source
interface
How many steps do LCP and NCP go through when setting up a connection?
1
2
3
4
Which router command would you use to test only layer-3 connectivity?
telnet
show cdp traffic
show interfaces
traceroute
On the 1900 switch, how do you enter User EXEC mode?
It comes up by default.
Enter the letter U in the menu.
Enter the letter K in the menu.
Enter the letter C in the menu.
Which of the following is a valid subnet mask value?
255.0.255.255
0.0.0.255
255.255.254.0
255.255.255.256
When you have configured PPP on an interface and use the show interfaces command, what state indicates the successful negotiation of a network layer protocol?
ACK
CHALLENGE
CLOSED
OPEN
Which protocol supports VLSM?
RIPv2
IGRP
RIP and IGRP
None of these
Which command assigns a default gateway to the 2950 switch?
(config)# default-gateway
(config-if)# default-gateway
(config-if)# ip default-gateway
(config)# ip default-gateway
OSPF uses __________ as a metric.
Bandwidth
Delay
Cost
Hop count
The root switch is the one elected with the __________ __________.
Lowest MAC address
Highest MAC address
Lowest switch ID
Highest switch ID
Your router is running RIP and OSPF and both routing protocols are learning 192.168.1.0/24. Which routing protocol will your router use for this route?
RIP
OSPF
If you wanted a list of parameters for the show command, you would type ________.
LOOK
VIEW
SHOW
Which VTP mode(s) will propagate VTP messages?
Client and server
Server
Client, server, and transparent
Transparent
When examining the IP routing table, an EIGRP route will be shown as what letter?
I
E
O
D
Which router command clears all of the static translations in the address translation table?
erase ip nat translation *
clear ip nat translation *
clear ip nat translation all
None of these commands
The 1900 switch supports ________ VLANs.
10
32
64
250
An OSPF's router ID is based on __________.
The lowest IP address on its loopback interface, if configured, or the lowest IP address onits active interfaces
The highest IP address on its loopback interface, if configured, or the highest IP address on its active interfaces
The highest IP address on its active interfaces, if configured, or the highest IP address on its loopback interfaces
The lowest IP address on its active interfaces, if configured, or the lowest IP address on its loopback interfaces
_________ defines how the Frame Relay DTE and DCE interact with each other.
DLCI
CIR
LMI
PMI
Annex A is which LMI standard?
Cisco
ITU-T Q.933
ANSI