Related Questions
What is the correct answer?
4
Out of the following, the alloy which has equal percentage of constituents, is
What is the correct answer?
4
Pick out the wrong statement about nucleate boiling.
A. Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface
B. Surface temperature is greater than the saturation temperature of the liquid
C. Heat transfer from the surface of the liquid is less than that in film boiling
D. The temperature is less than that of film boiling
What is the correct answer?
4
The product of a commercial direct reduction process is
D. Iron saturated with carbon
What is the correct answer?
4
Which of the following is not an ore of copper?
What is the correct answer?
4
Machinability of hard alloys and tool steels is improved by
What is the correct answer?
4
Electrical conductivities of semi-conductors are of the order of __________ ohm/cm.
What is the correct answer?
4
Milk is fat dispersed in water. It is an example of
What is the correct answer?
4
The maximum thickness of the metal which can be welded using ultrasonic welding is __________ mm.
What is the correct answer?
4
Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore?
A. High fusibility & fluidity
B. High thermal conductivity
D. High chemical activity
What is the correct answer?
4
The activity of pure hydrogen gas at 1000°C and 5 atm pressure
B. Is always greater than 1
D. Depends on the choice of the standard state
What is the correct answer?
4
The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the
What is the correct answer?
4
A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will
D. May increase or decrease; depends on the thickness of each layer
What is the correct answer?
4
The amount of water evaporated in kg per kg of fuel burnt in a boiler is called the __________ of a boiler.
B. Evaporation efficiency
What is the correct answer?
4
In a drilling process, the metal is removed by both shearing & extrusion. General purpose drills are made of
What is the correct answer?
4
Galvanic corrosion cannot be prevented by
C. Usage of largest possible anodic area
What is the correct answer?
4
Stellite is a __________ material.
D. Non-ferrous cast alloy cutting tool
What is the correct answer?
4
Drossing is a __________ operation.
What is the correct answer?
4
Hooke's law
A. Applies to elastic deformation
B. Applies beyond limit of proportionality in stress-strain curve
C. States that stress is inversely proportional to strain upto elastic limit
What is the correct answer?
4
A solution which resists change in its pH value on addition of acid/alkali is called the __________ solution.
What is the correct answer?
4
On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal.
What is the correct answer?
4
Production of a hollow product by inflation of a tube or parison is called the __________ process.
What is the correct answer?
4
For which pair of the fuel gases, calorific value (C.V.) of one fuel is almost double that of the other on volume basis (i.e., kcal/Nm3) while the C.V. is same on weight basis (i.e., kcal/kg)?
C. Sewage gas and gobar gas
D. B.F gas and coke oven gas
What is the correct answer?
4
Pick out the wrong statement.
A. Seam welding, projection welding & spot welding are the classification of electrical resistance welding
B. Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded)
C. In spot welding, two pieces to be joined are overlapped and placed between two electrodes
D. Mild steel sheet cannot be spot welded
What is the correct answer?
4
The fugacity of liquid water at 298 K is approximately 3171 Pa. Considering the ideal heat of vaporisation as 43723 J/gm.mole, its fugacity at 300 K would be
What is the correct answer?
4
For a first order chemical reaction, the concentration of the reactant decreases __________ with time.
What is the correct answer?
4
Brazing is the joining of metals
A. Without melting the base metal
B. With a non-ferrous filler
What is the correct answer?
4
The lightest non-inflammable gas is
What is the correct answer?
4
The best guide to judge the general quality of water is the measurement of its
B. Electrical conductivity
D. Dissolved oxygen content
What is the correct answer?
4
Which of the following is a boiler accessory
i.e., not a boiler mounting?
What is the correct answer?
4
Use of water as a manometric liquid suffers from the disadvantage of its